DeWalt D55166 Guide D'utilisation page 4

English
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE
HAZARD

DANGER: RISK OF EXPLOSION OR FIRE
What Can Happen How to Prevent It
It is normal for electrical contacts
within the motor and pressure
switch to spark.
If electrical sparks from
compressor come into contact
with flammable vapors, they may
ignite, causing fire or explosion.
Restricting any of the compressor
ventilation openings will cause
serious overheating and could
cause fire.
Unattended operation of this
product could result in personal
injury or property damage. To
reduce the risk of fire, do not
allow the compressor to operate
unattended.
HAZARD

DANGER: RISK TO BREATHING (Asphyxiation)
What Can Happen How to Prevent It
The compressed air directly from
your compressor is not safe for
breathing. The air stream may
contain carbon monoxide, toxic
vapors, or solid particles from
the air tank. Breathing these
contaminants can cause serious
injury or death.
2
Always operate the compressor
in a well ventilated area free of
combustible materials, gasoline, or
solvent vapors.
If spraying flammable materials,
locate compressor at least 20'
(6.1 m) away from spray area. An
additional length of air hose may
be required.
Store flammable materials in
a secure location away from
compressor.
Never place objects against or on
top of compressor.
Operate compressor in an open area
at least 12" (30.5 cm) away from
any wall or obstruction that would
restrict the flow of fresh air to the
ventilation openings.
Operate compressor in a clean, dry
well ventilated area. Do not operate
unit in any confined area. Store
indoors.
Always remain in attendance with
the product when it is operating.
Always turn off and unplug unit
when not in use.
Never use air obtained directly
from the compressor to supply
air for human consumption. The
compressor is not equipped with
suitable filters and in-line safety
equipment for human consumption.
What Can Happen How to Prevent It
Exposure to chemicals in dust
created by power sanding,
sawing, grinding, drilling, and
other construction activities may
be harmful.
Sprayed materials such as paint,
paint solvents, paint remover,
insecticides, weed killers, may
contain harmful vapors and
poisons.
HAZARD

WARNING: RISK OF BURSTING
Air Tank: On February 26, 2002, the U.S. Consumer Product
Safety Commission published Release # 02–108 concerning
air compressor tank safety:
Air compressor receiver tanks do not have an infinite
life. Tank life is dependent upon several factors, some of
which include operating conditions, ambient conditions,
proper installations, field modifications, and the level of
maintenance. The exact effect of these factors on air receiver
life is difficult to predict.
If proper maintenance procedures are not followed, internal
corrosion to the inner wall of the air receiver tank can cause
the air tank to unexpectedly rupture allowing pressurized
air to suddenly and forcefully escape, posing risk of injury
to consumers.
Your compressor air tank must be removed from service by
the end of the year shown on your tank warning label.
The following conditions could lead to a weakening of the
air tank, and result in a violent air tank explosion:
What Can Happen How to Prevent It
Failure to properly drain
condensed water from air tank,
causing rust and thinning of the
steel air tank.
Modifications or attempted repairs
to the air tank.
Unauthorized modifications to
the safety valve or any other
components which control air tank
pressure.
Work in an area with good cross
ventilation. Read and follow the
safety instructions provided on the
label or safety data sheets for the
materials you are spraying. Always
use certified safety equipment:
NIOSH/MSHA respiratory protection
or properly fit ting face mask
designed for use with your specific
application.
Drain air tank daily or after each use.
If air tank develops a leak, replace it
immediately with a new air tank or
replace the entire compressor.
Never drill into, weld, or make
any modifications to the air tank
or its attachments. Never attempt
to repair a damaged or leaking air
tank. Replace with a new air tank.
The air tank is designed to
withstand specific operating
pressures. Never make adjustments
or parts substitutions to alter the
factory set operating pressures.