Voltage And Circuit Protection - DeWalt D55166 Guide D'utilisation

2. Pull coupler on Quick Connect
Quick Connect 5 plug on hose.
Grounding Instructions (Fig. H)

WARNING: Risk of Electrical Shock. In the event
of a short circuit, grounding reduces the risk of
shock by providing an escape wire for the electric
current. This air compressor must be properly
grounded.
The portable air compressor is equipped with a cord having
a grounding wire with an appropriate grounding plug
1. The cord set and plug 14
grounding pin 15 . This plug MUsT be used with a
grounded outlet 16 .
FIG. H
14
15
iMPORTAnT: The outlet being used must be installed
and grounded in accordance with all local codes and
ordinances.
2. Ensure the outlet being used has the same
configuration as the grounded plug. DO nOT UsE An
ADAPTER.
3. Inspect the plug and cord before each use. Do not use if
there are signs of damage.
4. If these grounding instructions are not completely
understood, or if in doubt as to whether the compressor
is properly grounded, have the installation checked by a
qualified electrician.

WARNING: Risk of Electrical Shock. IMPROPER
GROUNDING CAN RESULT IN ELECTRICAL SHOCK.
• Do not modify the plug provided. If it does not fit the
available outlet, a correct outlet should be installed
by a qualified electrician.
• Repairs to the cord set or plug MUST be made by a
qualified electrician.
Extension Cords
If an extension cord must be used, be sure it is:
• a 3-wire extension cord that has a 3-blade grounding
plug, and a 3-slot receptacle that will accept the plug
on the product in good condition no longer than 50'
(15.2 m) 12 gauge (AWG) or larger. [Wire size increases
as gauge number decreases. 10 AWG may also be used.
DO NOT USE 14, 16 OR 18 AWG.)]
NOTICE: Risk of Property Damage. The use of an
undersized extension cord will cause voltage to drop
resulting in power loss to the motor and overheating.
Instead of using an extension cord, increase the
working reach of the air hose by attaching another
length of hose to its end. Attach additional lengths of
hose as needed.
5 body back to release
14 .
with this unit contains a
16

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit
Requirements under Pump/Motor Specifications.

WARNING: Risk of Overheating. Certain air
compressors can be operated on a 15 amp circuit if
the following conditions are met.
• Voltage supply to circuit must comply with the National
Electrical Code.
• Circuit is not used to supply any other electrical needs.
• Extension cords comply with specifications.
• Circuit is equipped with a 15 amp circuit breaker or 15
amp time delay fuse. nOTE: If compressor is connected
to a circuit protected by fuses, use only time delay fuses.
Time delay fuses should be marked "D" in Canada and
"T" in the US.
If any of the above conditions cannot be met, or if operation
of the compressor repeatedly causes interruption of the
power, it may be necessary to operate it from a 20 amp
circuit. It is not necessary to change the cord set.
Compatibility
Air tools and accessories that are run off the compressor
must be compatible with petroleumbased products. If you
suspect that a material is not compatible with petroleum
products, an air line filter for removal of moisture and oil
vapor in compressed air is required.
nOTE: Always use an air line filter to remove moisture and
oil vapor when spraying paint.
Location
Place the air compressor in a clean, dry and well ventilated
area at least 12" (30.5 cm) away from the wall or other
obstructions that will interfere with the flow of air. Keep the
compressor away from areas that have dirt and/or volatile
fumes in the atmosphere. These impurities may clog the
intake filter and valves, causing inefficient operation.

WARNING: The air compressor pump and shroud are
designed to allow for proper cooling. The ventilation
openings on the compressor are necessary to
maintain proper operating temperature. Do not place
rags or other containers on or near these openings.
Place the air compressor on a flat surface resting on the
rubber feet and wheels.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Preparation for Use
Pre-start Checklist (Fig. A, C)
1. Ensure the On/Off switch
2. Plug the power cord into the correct branch circuit
receptacle. See Voltage and Circuit Protection under
Installation.
English
1 is in the OFF position.
7