Télécharger Imprimer la page

Lindy IPower Strip 4 LITE Manuel Utilisateur

Publicité

Liens rapides

Données Techniques
Modèle
IPower Switch 4 LITE
No. 32450
Port d'accès distant
Ethernet 10Base-T, RJ-45
Alimentation IN / OUT
1x IEC Mâle / 4x IEC Femelle
Alimentation Max. sur IN
230VAC 2300VA (10A@230V)
Alimentation Max. sur OUT
Max. 8A par sortie, total 10A
Température en utilisation
+5°C ... 40°C, pour usage intérieur uniquement
Humidité
5 à 85% rel.H. non condensé
Dimensions (HXLXP), Poids
44.5 (1U) x 441 x 63 mm, 1.4kg
European EMC Directive 89/336/EEC CE statement
This equipment complies with the requirement for CE mentioned in the European Directive 89/336/EC and
Standards EN55022 and EN55024.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B Digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced technician for help
You are cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
For Commercial Use
Tested to Comply with
FCC Standards
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (AUG 2004)
IPower Switch 8 LITE
No. 32451
2x IEC Mâle / 8x IEC Femelle
230VAC 2x2300VA, 2x(10A@230V)
Max. 8A par sortie, total 2x10A
44.5 (1U) x 788 x 63 mm, 2.3kg
IPower Strip LITE
Manuel Utilisateur
(Version 8/2004 Firmware Version 1.18, la version fournie peut être supérieure)
Modèle 1 IN / 4 OUT: LINDY No. 32450
Modèle 2 IN / 8 OUT: LINDY No. 32451
www.LINDY.com
For Commercial Use
Tested to Comply with
FCC Standards
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (AUG 2004)
Français

Publicité

loading

Sommaire des Matières pour Lindy IPower Strip 4 LITE

  • Page 1 For Commercial Use Tested to Comply with For Commercial Use FCC Standards Tested to Comply with FCC Standards © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (AUG 2004) © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - SECOND EDITION (AUG 2004)
  • Page 2 Manuel en Français Manuel en Français Caractéristiques Connexion au secteur • Le rack d’alimentation est alimenté par ENTREE 1 (9). Connectez le câble d’alimentation fourni à ENTREE 1 , et Rack d’alimentation à accès distant avec connexion via IP • ensuite au secteur.

Ce manuel est également adapté pour:

Ipower strip 8 lite3245032451