gefran GFX4-IR PROFINET Manuel Utilisateur page 34

Address Name
FU_TA_ZONE_3
+ 132.0
H_PB_ZONE_3
+ 134.0
H_IT_ZONE_3
+ 136.0
H_DT_ZONE_3
+ 138.0
HI_S_ZONE_3
+ 140.0
HI_L_ZONE_3
+ 142.0
TYP_ZONE_4
+ 144.0
PS_TA_ZONE_4
+ 146.0
AL_ZONE_4
+ 148.0
HD_2_ZONE_4
+ 150.0
HD_5_ZONE_4
+ 152.0
CTR_ZONE_4
+ 154.0
PS_TM_ZONE_4
+ 156.0
PS_OF_ZONE_4
+ 158.0
HB_T_ZONE_4
+ 160.0
HB_P_ZONE_4
+ 162.0
IR_00_ZONE_4
+ 164.0
IR_01_ZONE_4
+ 166.0
IR_02_ZONE_4
+ 168.0
IR_03_ZONE_4
+ 170.0
IR_04_ZONE_4
+ 172.0
IR_05_ZONE_4
+ 174.0
IR_06_ZONE_4
+ 176.0
P_ON_T_ZONE_4
+ 178.0
FU_TA_ZONE_4
+ 180.0
H_PB_ZONE_4
+ 182.0
H_IT_ZONE_4
+ 184.0
H_DT_ZONE_4
+ 186.0
HI_S_ZONE_4
+ 188.0
HI_L_ZONE_4
+ 190.0
= 192.0
34
Initial
Type
value
INT 4803 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION
(ZONE 3)
INT 4101 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 3)
INT 4103 INTEGRAL HEATING TIME (ZONE 3)
INT 4104 DERIVATIVE HEATING TIME (ZONE 3)
INT 4498 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 3)
INT 4239 UPPER LIMIT OF SETPOINT (ZONE 3)
INT 8592 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT
(ZONE 4)
INT 8898 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 4)
INT 8387 SELECT NUMBER OF ENABLED ALARMS (ZONE 4)
INT 8852 ENABLE POWER FAULT ALARM (ZONE 4)
INT 8895 ENABLE TRIGGER MODES (ZONE 4)
INT 8372 TYPE OF CONTROL (ZONE 4)
INT 8897 DURATION OF PHASE ANGLE SOFTSTART RAMP (ZONE 4)
INT 8821 MINIMUM NON CONDUCTION TIME TO REACTIVATE THE PHASE
SOFTSTART RAMP (ZONE 4)
INT 8248 DELAY TIME FOR ACTIVATION OF HB ALARM (ZONE 4)
INT 8929 PERCENTAGE HB ALARM SETPOINT OF CURRENT READ IN HB
CALIBRATION (ZONE 4)
INT 8950 CT INPUT AT HB CALIBRATION PHASE 0 (FOR IR LAMPS) (ZONE 4)
INT 8951 CT INPUT AT HB CALIBRATION PHASE 1 (FOR IR LAMPS) (ZONE 4)
INT 8952 CT INPUT AT HB CALIBRATION PHASE 2 (FOR IR LAMPS) (ZONE 4)
INT 8953 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 4)
INT 8959 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA
MODE) (ZONE 4)
INT 8960 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA
MODE) (ZONE 4)
INT 8961 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA
MODE) (ZONE 4)
INT 8891 SWITCHING ON MODE (ZONE 4)
INT 8899 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION
(ZONE 4)
INT 8197 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 4)
INT 8199 INTEGRAL HEATING TIME (ZONE 4)
INT 8200 DERIVATIVE HEATING TIME (ZONE 4
INT 8594 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 4)
INT 8335 UPPER LIMIT OF SETPOINT (ZONE 4
END_
STRUCT
Comment
80992D_MSW_PROFINET_GFX4-IR_01-2021_FRA