gefran GFX4-IR PROFINET Manuel Utilisateur page 33

Address Name
PS_OF_ZONE_2
+ 62.0
HB_T_ZONE_2
+ 64.0
HB_P_ZONE_2
+ 66.0
IR_00_ZONE_2
+ 68.0
IR_01_ZONE_2
+ 70.0
IR_02_ZONE_2
+ 72.0
IR_03_ZONE_2
+ 74.0
IR_04_ZONE_2
+ 76.0
IR_05_ZONE_2
+ 78.0
IR_06_ZONE_2
+ 80.0
P_ON_T_ZONE_2
+ 82.0
FU_TA_ZONE_2
+ 84.0
H_PB_ZONE_2
+ 86.0
H_IT_ZONE_2
+ 88.0
H_DT_ZONE_2
+ 90.0
HI_S_ZONE_2
+ 92.0
HI_L_ZONE_2
+ 94.0
TYP_ZONE_3
+ 96.0
PS_TA_ZONE_3
+ 98.0
AL_ZONE_3
+ 100.0
HD_2_ZONE_3
+ 102.0
HD_5_ZONE_3
+ 104.0
CTR_ZONE_3
+ 106.0
PS_TM_ZONE_3
+ 108.0
PS_OF_ZONE_3
+ 110.0
HB_T_ZONE_3
+ 112.0
HB_P_ZONE_3
+ 114.0
IR_00_ZONE_3
+ 116.0
IR_01_ZONE_3
+ 118.0
IR_02_ZONE_3
+ 120.0
IR_03_ZONE_3
+ 122.0
IR_04_ZONE_3
+ 124.0
IR_05_ZONE_3
+ 126.0
IR_06_ZONE_3
+ 128.0
P_ON_T_ZONE_3
+ 130.0
80992D_MSW_PROFINET_GFX4-IR_01-2021_FRA
Initial
Type
value
INT 2677 MINIMUM NON CONDUCTION TIME TO REACTIVATE THE PHASE
SOFTSTART RAMP (ZONE 2)
INT 2104 DELAY TIME FOR ACTIVATION OF HB ALARM (ZONE 2)
INT 2785 PERCENTAGE HB ALARM SETPOINT OF CURRENT READ IN HB
CALIBRATION (ZONE 2)
INT 2806 CT INPUT AT HB CALIBRATION PHASE 0 (FOR IR LAMPS) (ZONE 2)
INT 2807 CT INPUT AT HB CALIBRATION PHASE 1 (FOR IR LAMPS) (ZONE 2)
INT 2808 CT INPUT AT HB CALIBRATION PHASE 2 (FOR IR LAMPS) (ZONE 2)
INT 2809 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 2)
INT 2815 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA
MODE) (ZONE 2)
INT 2816 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA
MODE) (ZONE 2)
INT 2817 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA
MODE) (ZONE 2)
INT 2747 SWITCHING ON MODE (ZONE 2)
INT 2755 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION
(ZONE 2)
INT 2053 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 2)
INT 2055 INTEGRAL HEATING TIME (ZONE 2)
INT 2056 DERIVATIVE HEATING TIME (ZONE 2)
INT 2450 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 2)
INT 2191 UPPER LIMIT OF SETPOINT (ZONE 2)
INT 4496 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT
(ZONE 3)
INT 4802 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 3)
INT 4291 SELECT NUMBER OF ENABLED ALARMS (ZONE 3)
INT 4756 ENABLE POWER FAULT ALARM (ZONE 3)
INT 4799 ENABLE TRIGGER MODES (ZONE 3)
INT 4276 TYPE OF CONTROL (ZONE 3)
INT 4801 DURATION OF PHASE ANGLE SOFTSTART RAMP (ZONE 3)
INT 4725 MINIMUM NON CONDUCTION TIME TO REACTIVATE THE PHASE
SOFTSTART RAMP (ZONE 3)
INT 4152 DELAY TIME FOR ACTIVATION OF HB ALARM (ZONE 3)
INT 4833 PERCENTAGE HB ALARM SETPOINT OF CURRENT READ IN HB
CALIBRATION (ZONE 3)
INT 4854 CT INPUT AT HB CALIBRATION PHASE 0 (FOR IR LAMPS) (ZONE 3)
INT 4855 CT INPUT AT HB CALIBRATION PHASE 1 (FOR IR LAMPS) (ZONE 3)
INT 4856 CT INPUT AT HB CALIBRATION PHASE 2 (FOR IR LAMPS) (ZONE 3)
INT 4857 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 3)
INT 4863 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA
MODE) (ZONE 3)
INT 4864 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA
MODE) (ZONE 3)
INT 4865 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA
MODE) (ZONE 3)
INT 4795 SWITCHING ON MODE (ZONE 3)
Comment
33