gefran GFX4-IR PROFINET Manuel Utilisateur page 32

UDT7
Liste des adresses Modbus des paramètres utilisés dans la FB15
Address Name
0.0
TYP_ZONE_1
+ 0.0
PS_TA_ZONE_1
+ 2.0
AL_ZONE_1
+ 4.0
HD_2_ZONE_1
+ 6.0
HD_5_ZONE_1
+ 8.0
CTR_ZONE_1
+ 10.0
PS_TM_ZONE_1
+ 12.0
PS_OF_ZONE_1
+ 14.0
HB_T_ZONE_1
+ 16.0
HB_P_ZONE_1
+ 18.0
IR_00_ZONE_1
+ 20.0
IR_01_ZONE_1
+ 22.0
IR_02_ZONE_1
+ 24.0
IR_03_ZONE_1
+ 26.0
IR_04_ZONE_1
+ 28.0
IR_05_ZONE_1
+ 30.0
IR_06_ZONE_1
+ 32.0
P_ON_T_
+ 34.0
ZONE_1
FU_TA_ZONE_1
+ 36.0
H_PB_ZONE_1
+ 38.0
H_IT_ZONE_1
+ 40.0
H_DT_ZONE_1
+ 42.0
HI_S_ZONE_1
+ 44.0
HI_L_ZONE_1
+ 46.0
TYP_ZONE_2
+ 48.0
PS_TA_ZONE_2
+ 50.0
AL_ZONE_2
+ 52.0
HD_2_ZONE_2
+ 54.0
HD_5_ZONE_2
+ 56.0
CTR_ZONE_2
+ 58.0
PS_TM_ZONE_2
+ 60.0
32
Initial
Type
value
STRUCT
INT 1424 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT (ZONE 1)
INT 1730 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 1)
INT 1219 SELECT NUMBER OF ENABLED ALARMS (ZONE 1)
INT 1684 ENABLE POWER FAULT ALARM (ZONE 1)
INT 1727 ENABLE TRIGGER MODES (ZONE 1)
INT 1204 TYPE OF CONTROL (ZONE 1)
INT 1729 DURATION OF PHASE ANGLE SOFTSTART RAMP (ZONE 1)
INT 1653 MINIMUM NON CONDUCTION TIME TO REACTIVATE THE PHASE
SOFTSTART RAMP (ZONE 1)
INT 1080 DELAY TIME FOR ACTIVATION OF HB ALARM (ZONE 1)
INT 1761 PERCENTAGE HB ALARM SETPOINT OF CURRENT READ IN HB
CALIBRATION (ZONE 1)
INT 1782 CT INPUT AT HB CALIBRATION PHASE 0 (FOR IR LAMPS) (ZONE 1)
INT 1783 CT INPUT AT HB CALIBRATION PHASE 1 (FOR IR LAMPS) (ZONE 1)
INT 1784 CT INPUT AT HB CALIBRATION PHASE 2 (FOR IR LAMPS) (ZONE 1)
INT 1785 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 1)
INT 1791 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA
MODE) (ZONE 1)
INT 1792 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA
MODE) (ZONE 1)
INT 1793 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA
MODE) (ZONE 1)
INT 1723 SWITCHING ON MODE (ZONE 1)
INT 1731 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION
(ZONE 1)
INT 1029 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 1)
INT 1031 INTEGRAL HEATING TIME (ZONE 1)
INT 1032 DERIVATIVE HEATING TIME (ZONE 1)
INT 1426 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 1)
INT 1167 UPPER LIMIT OF SETPOINT (ZONE 1)
INT 2448 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT
(ZONE 2)
INT 2754 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 2)
INT 2243 SELECT NUMBER OF ENABLED ALARMS (ZONE 2)
INT 2708 ENABLE POWER FAULT ALARM (ZONE 2)
INT 2751 ENABLE TRIGGER MODES (ZONE 2
INT 2228 TYPE OF CONTROL (ZONE 2)
INT 2753 DURATION OF PHASE ANGLE SOFTSTART RAMP (ZONE 2)
Comment
80992D_MSW_PROFINET_GFX4-IR_01-2021_FRA