gefran GFX4-IR PROFINET Manuel Utilisateur page 36

Address Name
Ir_03_Zone_2
+ 74.0
Ir_04_Zone_2
+ 76.0
Ir_05_Zone_2
+ 78.0
Ir_06_Zone_2
+ 80.0
P_On_t_Zone_2
+ 82.0
Fu_tA_Zone_2
+ 84.0
h_Pb_Zone_2
+ 86.0
h_It_Zone_2
+ 88.0
h_dt_Zone_2
+ 90.0
HI_S_Zone_2
+ 92.0
HI_L_Zone_2
+ 94.0
Typ_Zone_3
+ 96.0
PS_tA_Zone_3
+ 98.0
AL_Zone_3
+ 100.0
hd_2_Zone_3
+ 102.0
hd_5_Zone_3
+ 104.0
Ctr_Zone_3
+ 106.0
PS_tm_Zone_3
+ 108.0
PS_oF_Zone_3
+ 110.0
Hb_t_Zone_3
+ 112.0
Hb_P_Zone_3
+ 114.0
Ir_00_Zone_3
+ 116.0
Ir_01_Zone_3
+ 118.0
Ir_02_Zone_3
+ 120.0
Ir_03_Zone_3
+ 122.0
Ir_04_Zone_3
+ 124.0
Ir_05_Zone_3
+ 126.0
Ir_06_Zone_3
+ 128.0
P_On_t_Zone_3
+ 130.0
Fu_tA_Zone_3
+ 132.0
h_Pb_Zone_3
+ 134.0
h_It_Zone_3
+ 136.0
h_dt_Zone_3
+ 138.0
HI_S_Zone_3
+ 140.0
HI_L_Zone_3
+ 142.0
Typ_Zone_4
+ 144.0
PS_tA_Zone_4
+ 146.0
AL_Zone_4
+ 148.0
hd_2_Zone_4
+ 150.0
hd_5_Zone_4
+ 152.0
36
Initial
Type
value
INT 160 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 2)
INT 150 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA MODE)
(ZONE 2)
INT 140 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA MODE)
(ZONE 2)
INT 120 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA MODE)
(ZONE 2)
INT 1 SWITCHING ON MODE (ZONE 2)
INT 500 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION (ZONE 2)
INT 10 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 2)
INT 1 INTEGRAL HEATING TIME (ZONE 2)
INT 0 DERIVATIVE HEATING TIME (ZONE 2)
INT 200 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 2)
INT 200 UPPER LIMIT OF SETPOINT (ZONE 2)
INT 40 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT(ZONE 3)
INT 800 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 3)
INT 16 SELECT NUMBER OF ENABLED ALARMS (ZONE 3)
INT 11 ENABLE POWER FAULT ALARM (ZONE 3)
INT 155 ENABLE TRIGGER MODES (ZONE 3)
INT 198 TYPE OF CONTROL (ZONE 3)
INT 100 DURATION OF PHASE ANGLE SOFTSTART RAMP (ZONE 3)
INT 1 MINIMUM NON CONDUCTION TIME TO REACTIVATE THE PHASE
SOFTSTART RAMP (ZONE 3)
INT 4 DELAY TIME FOR ACTIVATION OF HB ALARM (ZONE 3)
INT 800 PERCENTAGE HB ALARM SETPOINT OF CURRENT READ IN HB CALI-
BRATION (ZONE 3)
INT 240 CT INPUT AT HB CALIBRATION PHASE 0 (FOR IR LAMPS) (ZONE 3)
INT 200 CT INPUT AT HB CALIBRATION PHASE 1 (FOR IR LAMPS) (ZONE 3)
INT 180 CT INPUT AT HB CALIBRATION PHASE 2 (FOR IR LAMPS) (ZONE 3)
INT 160 CT INPUT AT HB CALIBRATION PHASE 3 (FOR IR LAMPS) (ZONE 3)
INT 150 CT INPUT AT HB CALIBRATION PHASE 4 (FOR IR LAMPS IN PA MODE)
(ZONE 3)
INT 140 CT INPUT AT HB CALIBRATION PHASE 5 (FOR IR LAMPS IN PA MODE)
(ZONE 3)
INT 120 CT INPUT AT HB CALIBRATION PHASE 6 (FOR IR LAMPS IN PA MODE)
(ZONE 3)
INT 1 SWITCHING ON MODE (ZONE 3)
INT 500 MAXIMUM LIMIT OF RMS CURRENT IN NORMAL OPERATION (ZONE 3)
INT 10 PROPORTIONAL BAND FOR HEATING OR HYSTERESIS IN ON-OFF
CONTROL (ZONE 3)
INT 1 INTEGRAL HEATING TIME (ZONE 3)
INT 0 DERIVATIVE HEATING TIME (ZONE 3)
INT 200 MAXIMUM LIMIT OF MAIN INPUT SCALE (ZONE 3)
INT 200 UPPER LIMIT OF SETPOINT (ZONE 3)
INT 40 TYPE OF PROBE, SIGNAL AND SCALE OF MAIN INPUT(ZONE 4)
INT 800 MAXIMUM PREAK CURRENT LIMIT DURING PHASE SOFTSTART
(ZONE 4)
INT 16 SELECT NUMBER OF ENABLED ALARMS (ZONE 4)
INT 11 ENABLE POWER FAULT ALARM (ZONE 4)
INT 155 ENABLE TRIGGER MODES (ZONE 4)
Comment
80992D_MSW_PROFINET_GFX4-IR_01-2021_FRA