4 2 Setting The Start Address And; The Number Of Dmx Channels; 4 3 Using Subaddresses - Monacor International IMG STAGELINE ODP-120/6COL Mode D'emploi

Projecteur dmx à leds
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 24
4.4.2 Setting the start address and

the number of DMX channels

For separate control of all DMX units connected
to the light controller, each unit must have its
own start address . Example: If the first DMX
channel of the ODP-120/6COL is to be con-
trolled by the light controller via DMX address 6,
set the start address on the ODP-120/6COL to 6 .
The other DMX channels of the ODP-120/6COL
will then be automatically assigned to the sub-
sequent addresses . Examples for various start
addresses:
Number
Start
of DMX
address
channels
1
3
6
1
6
6
1
8
25
1
10
56
1
13
500
Fig. 10 DMX address assignment
1) Select the main menu item [DMX] .
2) Press the button ENTER . The display will show
either [ADDRESS] and the start address or
[CHANNEL] and the number of DMX chan-
nels required .
3) Use the buttons UP and DOWN to switch
between [ADDRESS] and [CHANNEL] .
4) To set the start address or the number of
channels, select the corresponding menu
item and press the button ENTER . Use the
buttons UP and DOWN to make the settings
and press the button ENTER to confirm .
Next possible
Addresses
start address for
used by the
the subsequent
ODP-120/6COL
DMX unit
3
6 – 8
1 – 6
6 – 11
12
1 – 8
25 – 32
33
1 – 10
11
56 – 65
66
1 – 13
14
500 – 512
5) Set all further ODP-120/6COL spotlights to be
controlled in sync to the same start address
and to the same number of channels .
The spotlight can now be controlled by DMX .
The DMX functions can be found in chapter
5 .1 on page 22 . If the ODP-120/6COL does not
receive any DMX control signal, the dot next to
DMX in the top left corner of the display will
keep flashing in red .
If the spotlight was set to independent op-
eration in between, go back to the main menu
item [DMX] to activate the DMX mode .
4.4.3 Using subaddresses
In the 13-channel mode, subaddresses can be
used to independently control up to 66 ODP-
4
120/6COL one after the other via a single DMX
9
start address . Thus, the maximum possible num-
7
ber of DMX units is substantially increased . DMX
channel 13 is used to select units with a sub-
9
address . Units having the same start address
and different subaddresses may be controlled
in sync if DMX channel 13 is set to a DMX value
less than 10 .
1) Select the main menu item [SET UP] .
2) Press the button ENTER . One of the submenu
items will be displayed .
3) Use the button UP or DOWN to select the
menu item [ID number] .
4) Press the button ENTER and use the button
UP or DOWN to select the subaddress . In the
setting OFF, DMX channel 13 is without func-
tion and can be used for the next DMX unit .
5) Press the button ENTER to save the setting .
6) To be able to operate the spotlight via the
subaddress, set DMX channel 13 on the light
controller to the DMX value corresponding to
the subaddress (refer to Fig . 16 on page 23) .
19

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

38.7490

Table des Matières