Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
SPECIFIC SAFETY RULES
1. Never touch moving parts.
Never place your hands, fi ngers or other body parts
near the tool's moving parts.
2. Never operate without all guards in place.
Never operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
3. Use right tool.
Don't force small tool or attachment to do the job of a
heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
4. Handle tool correctly.
Do not drop or throw the tool.
5. Defi nitions for symbols.
V ................volts
— ...............direct current
---
n
o ..............no load speed
---/min.........revolutions or reciprocation per minute
Hz ..............hertz
A ................amperes
6. Keep all screws, bolts and covers tightly in
place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
7. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
8. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to yourself or others.
Blades, cutting implements and accessories which
have been mounted to the tool should be secure and
tight.
9. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
10. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dried thoroughly.
11. Keep motor air vent clean.
The tool's motor air vent must be kept clean so that
air can freely fl ow at all times. Check for dust build-up
frequently.
12. NEVER leave tool running unattended. Turn
power off .
Don't leave tool until it comes to a complete stop.
13. NEVER touch the blade with bare hands after
operation.
14. For this mode, the saw blades should be 165 mm.
15. Because the cordless circular saw operates by
battery power, be aware of the fact that it can begin
to operate at any time.
16. When working at elevated locations, clear the area of
other people and aware of conditions below you.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY AND BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers and
battery. To avoid these risks, follow these basic
safety instructions:
CAUTION
USE ONLY metabo HPT BATTERY TYPE BSL18
SERIES. OTHER TYPES OF BATTERIES MAY
BURST AND CAUSE INJURY!
1. Do not use a battery pack or appliance that is
damaged or modifi ed. Damaged or modifi ed batteries
may exhibit unpredictable behavior resulting in fi re,
explosion or risk of injury.
2. Do not expose a battery pack or appliance to
fire or excessive temperature. Exposure to fire
or temperature above 265°F (130°C) may cause
explosion.
3. This manual contains important safety and operating
instructions for battery charger Model UC18YKSL.
4. To reduce risk of injury, charge metabo HPT
rechargeable battery type BSL18 series. Other type
of batteries may burst causing personal injury and
damage.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fi re and electric shock.
If extension cord must be used make sure:
a.
That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b.
That extension cord is properly wired and in
good electrical condition; and
c.
That wire size is large enough for AC ampere
rating of battery charger as specifi ed in Table 1.
English
5
Publicité
Table des Matières
