Bosch PSM VENTARO 1400 Instructions D'emploi page 16

Masquer les pouces Voir aussi pour PSM VENTARO 1400:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 19
OBJ_BUCH-2 609 932 412-001.book Page 4 Thursday, January 13, 2005 12:48 PM
Connecting the Multi Sander
(see figure F)
The supplied multi sander 1 can be used in the "Extrac-
tion" operating mode of the vacuum cleaner 4.
The closing cover with blower filter 12 should be
inserted in the holder 10. The blower filter cleans the
blown out air.
Insert the vacuum hose 3 into the vacuum hose con-
nection of the multi sander 22.
Ensure that a dust bag is inserted in the vacuum
cleaner when sanding.
To remove the vacuum hose 3, rotate the hose a little
and pull it off.
Replacing the Sanding Sheet
(see figure G)
When attaching a new sanding sheet, remove any dust
or debris from the sanding plate 24 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that
the punched holes in the sanding sheet match with the
holes in the sanding plate.
The sanding plate 24 is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 25, free the Velcro
backing of the sanding plate 24 from any debris by tap-
ping against it in order to enable optimum adhesion.
The multi sander is equipped with 2 sanding sheets.
Depending on their condition of wear, these can also
be changed individually.
Use the multi sander only when both sanding
sheets are attached.
Only use sanding sheets with the same grain
size.
Position the sanding sheet 25 flush alongside one edge
of the sanding plate 24, then lay the sanding sheet onto
the sanding plate and press it against it with a light turn-
ing motion in clockwise direction.
To remove the sanding sheet 25, grasp it at one of the
tips and pull it off from the sanding plate 24.
Sanding sheets of the Bosch Delta Sander can be
used.
Sanding accessories, such as fleece pads/polishing
cloth pads, are attached to the sanding plate in the
same manner.
2 609 932 412 • 13.1.05
Selecting the Sanding Sheet
Depending on the material to be worked and the
required rate of material removal, different sanding
sheets are available:
For the working of all
wooden materials
For coarse-sanding, e. g. of
rough, unplaned beams and
boards
For face sanding and planing
small irregularities
For finish and fine sanding of
hard woods
For the working of
paint/enamel coats or
primers and fillers
For sanding off paint
For sanding primer
For final sanding of primers
before coating
For reworking or polishing, especially of metal and
stone, use fleece/polishing cloth pad.
Depending on the desired surface quality of the work-
piece, different fleece types or polishing cloth pads are
to be used.
Replacing the Sanding Plate
(see figure H)
Slide the SDS button for release of the sanding
plate 23 all the way to the right.
Remove the sanding plate 24.
Guide the sanding plate 24 from below against the
sanding plate holder and firmly press them
together.
Slide the SDS button for release of the sanding
plate 23 all the way to the left.
If, e. g., the front tip of the sanding sheet is worn, you
can also remove the complete sanding plate and reat-
tach it turned by 120°.
English–4
Grain size
40—180
coarse
40
medium
80, 120
fine
180
40—180
coarse
40
medium
80, 120
fine
180

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

0603341030

Table des Matières