Grinding Wheel Replacement; Switching On - Switching Off - SPARKY HD Professional M 750 HD Notice Originale

▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position. If the plug is connected to
a receptacle while the power switch is in the
ON position, the power tool will start operat-
ing immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
WARNING: Always switch off and un-
plug the power tool prior to any adjustment,
servicing or maintenance.
▪ Make sure the grinding wheel diameter and
thickness do not exceed the values specified
on the name plate. The peripheral speed in-
dicated on the wheel must not be less than
80 m/s. The wheels must be stored according
the recommendations of the manufacturer.
▪ In case the work area is remote from the pow-
er source, use as short as practicable exten-
sion cord with proper cross-section.
▪ Check that the auxiliary handle is properly
mounted and reliably tightened.

SWITCHING ON - SWITCHING Off

Switching on: Push the back end of the ON/OFF
switch 7 down and then forward in the direction
of the arrow until its front end will sag, thus fix-
ing itself.
Switching off: press the back, lifted end of switch
7 and release it to return in its initial position.
ADjUSTING THE ROTATION SPEED
(M 750E HD, M 850E HD)
Continuous operation at low rpm is not recom-
mended for the following machines: М 750Е HD,
M 850E HD.
The rotation speed can be varied smoothly by
turning electronic regulator 8, placed on the
rear of the grinder. In the table below the rec-
ommended regulator positions for the different
areas of applications are specified:
Area of application
1. Plastics grinding with plastic disk
and abrasive cloth (paper)
2. Wood grinding and removing
Original instructions
Regulator position
A - C
B - D
lacquer and dye coatings
3. Metal grinding with plastic disk and
abrasive cloth (paper)
4. Dust removing with cup brush
5. Rough cleaning, metal or stone cutting
6. Polishing with plastic disk and
polishing jacket
Model M 850E HD is equipped with full-wave
electronics for
- Soft start and restriction of the starting cur-
rent;
- Speed pre-selection and control.
WHEEL GUARD
WARNING: The wheel guard 2.1 for
grinding wheel or the wheel guard 2.2 for
cutting wheel (for grinding wheel 4.1 or cut-
ting wheel 4.2 accordingly) must always be
mounted on the machine!
Its position can be different and depends on
which side the auxiliary handle is placed, as well
as when the machine is mounted on a stand.

GRINDING WHEEL REPLACEMENT

Secure spindle 1 by depressing the spindle lock
button 9 provided on the gear case.
WARNING:
while the spindle is still rotating!
(With this button depressed turn the spindle till
its pronounced going deeper). ). Unscrew the
fixing flange 5 by a lock nut wrench. Place the
new wheel on thesupport flange 3 with the in-
scriptions facing up, and screw down flange 5
facing its flat side towards the wheel, using the
lock nut wrench. Use blotters if the wheel has
been delivered with them. After replacing the
wheel operate the machine with the new wheel
in no load mode for one minute. Vibrating or
otherwise improperly rotating wheels must be
replaced immediately and discarded.
Cup brushes 10 are screwed directly on spindle
1 by means of an open-end spanner. (Check if
the brush thread length is sufficient to accept the
spindle thread.)
Grinding and polishing with abrasive sanding
disks is accomplished by means of plastic rub-
ber backing disk (pad) 11, under which sanding
disks and polishing jackets 12 are mounted.
Place plastic backing pad 11 on the support
flange 3 and secure it with lock nut 13, delivered
C - f
D - f
A - B
Never press button 9
9
G
EN