Telcoma Automations T201 Instructions Pour L'installation page 52

GB
TAB. 1 (see fig. 2)
Mor n. Mor n.
1 Motor M1
2 Motor M1
3 Motor M1
2 3 Capacitor
4 Motor M2
5 Motor M2
6 Motor M2
5 6 Capacitor
7 8 Flashing light
9 8 Light
10 11 Line
12 13 Auxiliares
Photocell/s
14 15
transmitter
15 16 Warning light
17 18 Electric lock
20 19 o 25 N.C. contact
21 19 o 25 N.C. contact
22 19 o 25 N.C. contact
23 19 o 25 N.C. contact
N.C. contact or
24 19 o 25
N.O. pushbutton
N.C. contact or
26 25 o 31
N.O. pushbutton
27 25 o 31 N.C. contact
28 25 o 31 N.O. pushbutton
29 25 o 31 N.C. contact
30 25 o 31 N.O. pushbutton
32 Receiver antenna Rx*
33 Receiver antenna Rx*
34 35 Auxiliares
36 Encoder 2
37 Encoder 2
38 Encoder 2
39 Encoder 1
40 Encoder 1
41 Encoder 1
Input Output
*ANTENNA: pay attention if a plug-in radio card is used, since the connector for antenna connection in certain models
is on the actual card.
52
Device V I max
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 4A
230Vac 1A
230Vac 1A
230Vac 6,3A
24Vac 150mA
24Vac 150mA
24Vac 100mA
12Vcc 1A
Max 24V 500mA
0 V
~20V
0 V
~20V
Function
Common M1
Close M1
Open M1
Motor breakaway M1
Common M2
Close M2
Open M2
Motor breakaway M2
Movement indicator
Courtesy light
C. unit power supply
Power supply
Transmitter power supply
for foto-test
Gate open
Mechanical lock
Closing limit switch (M1)
Opening limit switch (M1)
Photocell 1
Photocell 2
Jolly 2
Jolly 1
Fixed safety edge
Pedestrian gate
Stop
Step-by-step
Control unit
Braid
II° Receiver channel
Negative power supply
Positive power supply
Data
Negative power supply
Positive power supply
Data
Notes
The motor M1 is delayed for gate clo-sing.
In swing gate installations the motor M1 should
control theleaf with the electric lock.
See motor notes
The motor M2 is delayed for gateopening (with dip-
switch n. 11 set to ON)
See motor notes
On when the motor is working. Switchingon may be
anticipated (pre-blinking), seedipswitch No.5 functions
On, from start of movement to 3minutes after full closure
Connect to the 230Vac line. See"ELECTRICAL CONNECTIONS"
Permanent for photocells and auxiliaries power supply
Power supply for photocell transmitter (if the Foto test
function is used)
Use a 24V 2W max. bulb, see text
Active for a few seconds at everystart of opening
Connect this input if not used to thecommon terminal.
Connect this input if not used to thecommon terminal.
During closure it reverses the direc-tion.
Connect this input if not used tothe common terminal
Temporary stop during opening. During clo-sing
it reverses the direction. Connect thisinput to the
common terminal if it is notused.
See dipswitch No.3 and 4 functions.
If this input is not used, put dipswitches 3 and 4 to OFF.
See dipswitch No.3 and 4 functions.
If this input is not used, put dipswitches 3 and 4 to OFF.
Reverse the direction for a few seconds and the control unit
locks. Connect this input tothe common terminal if it is not used.
With 2 motors, opening is carried outby just motor
M1. With 1 motor, opening is for just 6 seconds.
Stop all functions. Connect this input ifnot used to the
common terminal.
See functions dipswitches No.1 and No.2
Connect an aerial suited to the receiver model
Only available if a two-channel radiocard is inserted
in the pre-installed connector (det. 13 of fig. 1).
See motor instructions