Specific Safety Rules And Symbols; Functional Description - Hilti SF 100-A Mode D'emploi

Maintain insert tools with care. Keep cutting insert
tools sharp and clean.
Properly maintained insert tools with sharp cutting edge
are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model.
Accessories that may be suitable for one tool may cre-
ate a risk of injury when used on another tool.
Service
Tool service must be performed only be qualified repair
personnel.
Service or maintenance performed by unqualified per-
sonnel may result in a risk of injury.
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual.
Use of unauthorized parts or failure to follow Mainte-
nance Instructions may create a risk of shock or injury.

Specific Safety Rules and Symbols

Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may con-
tact hidden wiring.
Contact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
WARNING: Some dust created by grinding, sanding,
cutting and drilling contains chemicals known to cause
cancer, birth defects, infertility or other reproductive
Functional description (typical)
Type of screw / application
Universal-type or chipboard screw:
in pine or chipboard:
Threaded screws (machine screws):
Screws in plastic anchors:
Screw:
Plastic anchor:
Twist drill in pine / hardwood:
Twist drill (HSS drill bit) in steel:
Holes in steel up to 6 mm (
") dia. drill bit:
predrill with 6 mm ( 1 /
4
Holesaws in chipboard:
4
Printed: 07.07.2013 | Doc-Nr: PUB / 5070586 / 000 / 00
") dia.:
1 /
4
harm; or serious and permanent respiratory or other
injury. Some examples of these chemicals are: lead from
leadbased paints, crystalline silica from bricks, concrete
and other masonry products and natural stone, arsenic
and chromium from chemicallytreated lumber. Your risk
from these exposures varies, depending on how often
you do this type of work. To reduce exposure to these
chemicals, the operator and bystanders should work
in a well-ventilated area, work with approved safety
equipment, such as respiratory protection appropriate
for the type of dust generated, and designed to filter
out microscopic particles and direct dust away from
the face and body. Avoid prolonged contact with dust.
Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth,
eyes, or to remain on your skin may promote absorption
of harmful chemicals.
The tool is not intended for use by children, by debil-
itated persons or those who have received no instruc-
tion or training.
Children must be instructed not to play with the tool.
Don't use the tool in water.
Water can damage the tool and battery pack and creates
risk of shocking the operator.
Ensure that the insert tools (drill bits, etc.) are equipped
with the appropriate connection end for the chuck
system in use and that they are locked in position cor-
rectly in the chuck.
A loose insert tool presents a risk of injury.
Take care to avoid concealed cables and pipes. Check
the area in which you are working beforehand, e. g.
using a metal detector.
Concealed electric cables or gas and water pipes pre-
sent a serious hazard if damaged while you are work-
ing.
Check of proper battery seating in the tool.
If the battery is not properly inserted, it can drop out
when working and cause an injury.
Size
") dia.
up to 4 mm ( 5 /
32
"–
above 4–6 mm ( 5 / 1 /
32 4
") dia.
up to 6 mm ( 1 /
4
") dia.
6 mm ( 1 /
4
") dia.
8 mm ( 5 /
16
") dia.
10 mm ( 3 /
8
") dia.
up to 6 mm ( 1 /
4
") dia.
up to 10 mm ( 3 /
8
") dia.
up to 63 mm (2 1 /
2
Speed
2nd speed
") dia.
1st speed
2nd speed
1st speed
2nd speed
2nd speed
1st speed
1st speed