Assembly; Operation; Care And Maintenance - Hilti SF 100-A Mode D'emploi

Assembly

It is essential that the safety precautions print-
ed in these operating instructions are read and observed
before the tool is used.
The SF100-A may be used only with the SBP10
or SFB105 battery.
Before it is used for the first time, it is essential
that a new battery is charged for 24 hours in normal
charging mode or up to 12 hours using the condition-
ing charging mode, thus permitting "forming" of the
battery cells to take place.
At low temperatures: Battery performance drops at low
temperatures. Store the battery at room temperature
when not in use.
At high temperatures: Do not store a battery where it
may be subjected to high temperatures (e.g. exposed
to the sun, at a window, behind a car windscreen or on
a radiator).
Do not completely run down the battery. The cells can
be damaged if the battery is completely discharged.

Operation

Insert tool insertion and removal
Use the safety catch
tentional switching on during transport or when insurt-
ing or removing an insert tool.
Quick-release chuck
An insert tool can be clamped or released without a chuck
key. When the screwdriver is switched off by the on-off
control switch, the spindle is locked. This is a help when
opening / tightening the quick-release chuck.
Battery removal
Battery release button
If the battery has to be changed, press in the two release
buttons using two fingers and pull the battery out of the
screwdriver.
Battery insertion
Push in the battery as far as it will go. There must be an
audible click.
Only the Hilti SBP10 or SFB105 batteries may be used.
Battery charging
Only the Hilti C 7/24, C 7/36-ACS, SFC7/18, TCU7/36 or
SBC12H battery charger may be used. Please refer to
the charger operating instructions for the charging
process.
If the SFB105 battery is charged in the old SBC 12 H
charger, a loss of capacity must be expected with this
Printed: 07.07.2013 | Doc-Nr: PUB / 5070586 / 000 / 00
as protection against unin-
kind of charging. Full capacity of the battery will be
obtained with the C 7/24, C 7/36-ACS, SFC 7/18 and
TCU7/36 chargers.
Speed selection
Two-speed switch
The speed can be selected using the mechanical two-
speed switch, i.e. 1 st speed: 0–350 r.p.m. or 2
0–1250 r.p.m. Only change speed when the screwdriv-
er is not running.
Torque selection
Torque clutch setting ring
The release torque (1–7 Nm) is obtained by turning the
setting ring to the desired torque level (setting 1–20).
At the drilling symbol (
blocked and the screwdriver gives its max. torque of
about 16 Nm (stalling torque) at this setting.
Reversing switch
The reversing switch is used to reverse the direction of
rotation of the chuck. A locking device prevents opera-
tion of the switch while the motor is running. The con-
trol switch is deactivated when the reversing switch
is in the central position.
Speed control
Switch with electronic speed control
The speed can be controlled infinitely from zero to max-
imum by slowly depressing the switch.

Care and maintenance

Before cleaning, remove the battery from the tool
in order to prevent inadvertent starting.
Care of the tool
-CAUTION-
Keep the power tool, especially its grip surfaces,
clean and free from oil and grease. Do not use clean-
ing agents which contain silicone.
The outer casing of the tool is made from impactre-
sistant plastic. Sections of the grip are made from a
synthetic rubber material. Never operate the tool when
the ventilation slots are blocked. Clean the ventilation
slots carefully using a dry brush. Do not permit for-
eign objects to enter the interior of the tool. Clean the
outside of the tool at regular intervals with a slightly
damp cloth. Do not use a spray, steam pressure clean-
ing equipment or running water for cleaning. This may
negatively affect the electrical safety of the tool.
Take care of your insert tools. Clean off dirt and dust
deposits. Always keep the connection end clean and
lightly greased.
SBP10 and SFB105 batteries
Keep the contact surfaces free of dust and lubricants.
nd speed:
), the torque clutch is
5