Rear Panel - BST SYMBOL-250 Manuel D'utilisation

SYMBOL-250
Each press of the PLAY/PAUSE Button causes the operation to change from play to pause or from pause to play. While in play mode the
green LED will glow, and while in pause mode the green LED will flash.
33. IN-OUT-RELOOP BUTTONS
- IN button : "cue ON THE FLY" - This function allows you to set a CUE POINT without music interruption ("on the fly"). This button also
sets the starting point of a seamless loop.
- OUT button :This button is used to set the ending point of a loop. A loop is started by pressing the IN BUTTON,pressing
the OUT BUTTON set the loop ending point. The loop will continue to play until the OUT BUTTON is pressed once again.
- RELOOP button : If a SEAMLESS LOOP has been made, but the player is not actively in SEAMLESS LOOP mode(a loop is not playing),
pressing the RELOOP button will instantly reactivate the SEAMLESS LOOP mode. To exit loop,press the OUT BUTTON. LOOP and
RELOOP will appear in the LCD DISPLAY when the RELOOP function is available.
34. SINGLE/ CONTINU BUTTON
This function allows you to choose between single track play or continuous track play (all tracks in order).Hold this button down for 1
second to activate the Auto Cue function.
35. TEMPO LOCK BUTTON
This button activates and deactivates the TEMPO LOCK function. This function allows you to use the PITCH KNOB (26) to speed up or
slow down playback speed without altering the tonal pitch of the track. When this function is not engaged the original tonal pitch of the track
will be altered giving you the "chipmunk" effect when a track is played at a high rate of speed, or the "James Earl Jones" effect when a
track is slowed to much.
36. PITCH BEND BUTTONS
(-) PITCH BEND Button : The (-) pitch bend function creates a momentary "Slow Down" in the song's BPM's(Beats per minute) while it is
playing. This will allow you to match the beats between two playing track's or other playing music source. Remember, this is a momentary
function. When you remove your finger from the pitch button,the BPM's will automatically return to normal. Holding down this button will
decrease the pitch to whatever the PITCH PERCENTAGE SELECTOR (38) is set to. Use this function to slow to another playing music
source. Be sure to notice that this function is a momentary pitch adjustment.
(+) PITCH BEND BUTTON : The (+) pitch bend function creates a momentary "BUMP" in the song's BPM's (Beats per minute) while it is
playing. This will allow you to match the beats between two playing song's or any other music source. Remember, this is a momentary
function. When you remove your finger from this button, the BPM's will automatically return to normal. Holding down this button will
increase the pitch to whatever the PITCH PERCENTAGE SELECTOR (38) is set to.
37. TIME MODE BUTTON
The TIME button will switch the time value described in the time meter between Elapsed playing time, and TRACK Remaining time.
38. PITCH PERCENTAGE SELECTION BUTTON
When the PITCH KNOB (30) is activated use this button to choose a pitch percentages of 4%, 8%, and 16%.
39. LCD DISPLAY
Display all kinds of information.

REAR PANEL

40. GROUND
The GND is a terminal for grounding turntables to eliminate hum.
41. CHANNEL 1 PHONO/AUX SELECTOR
Use the selector switch to switch from phono to aux level.
42. CHANNEL 1 AND 2 PHONO/AUX INPUTS
Connect on these inputs either a PHONO device as turntable or either a aux level device such as cd player or minidisc,
43. CHANNEL 1, 2, 3 AND 4 LINE INPUTS
Connect on these inputs a line level device such as cd player or minidisc,
44. ZONE OUTPUT
Unbalanced zone stereo program output provided by RCA sockets. Connect it to your secondary power amplifier
45. PFL ZONE OUTPUT
This stereo output is used to connect tape recorder, computer, other units of recording
46. UNBALANCED MASTER OUTPUT
Unbalanced output. Connect it to the inputs of the main power amplifier.
© Copyright LOTRONIC 2014 SYMBOL 250
BSTDJ.COM
Page 10