BST SYMBOL-250 Manuel D'utilisation page 9

SYMBOL-250
14. HEADPHONE LEVEL CONTROL
This control varies the volume in your headphones, the volume of the signal heard through the headphones.
15. CUE MIX
Slide this to mix the Cue channel and master in the headphones. When all the way to the left, only channels routed to the Cue
channel will be heard. When all the way right, only the master will be heard.
16. OUTPUT LEVEL CONTROLS
There are three outputs
- PFL zone : adjusts the PFL ZONE output volume.
- Zone : Is a second and adjustable stereo Master program output.
- Master : adjusts the main master output volume.
17. XFADER ASSIGN SWITCH
Use to assign any channel in each side of xfader
18. CHANNEL 1, 2, 3 AND 4 LEVEL CONTROL
The channel level slide control can be used to adjust the individual input to obtain the desired volume of each channel.
19. XFADER
This crossfader is fully assignable to any of the four main music channels set by the ASSIGN switches.
20. MIC ON/OFF
Turns the dedicated microphone input on or off.
21. MIC 1 LEVEL CONTROL
Correct setting of the controls for MIC 1 input GAIN is crucial for getting a good, strong signal without noise or distortion.
22. MIC 1 BASS TONE CONTROL
Mic 1 channel has a 2-band equalizer for tone shaping. The low control have fixed low frequencies and a boost/cut range of +/- 12dB
23. MIC 1 TREBLE TONE CONTROL
Mic 1 channel has a 2-band equalizer for tone shaping. The Treble control have fixed high frequencies and a boost/cut range of +/- 12dB
24. USB SOCKET
This is the USB port where you can insert a USB stick, USB card reader, or compatible external hard drive for playback.
25. SD SOCKET
This is where you load your SD card. Gently insert your SD Card into the slot.To eject your card, put the Media Operator in pause mode,
and then press the SD Card gently. The SD Card should "Pop" out.
26. PITCH BUTTON
This knob is used to adjust the playback pitch percentage. The knob is a set adjustment and will remain set until the pitch knob is moved or
the pitch function has been turned off. This adjustment can be made with or without a digital source loaded. The pitch adjustment will
remain even if the digital source has been removed and will reflect on any other digital source loaded into the player. That is to say, if you
set a +2% pitch on one digital source, remove that source and load another, that source too will have a +2% pitch. The amount of pitch
being applied will be displayed in the LCD .
27. FRAME SEARCH BUTTONS
The search buttons will let you scan through a track, either backwards or forwards, frame by frame. If you hold either of the buttons down
you will search faster through the frames.
28. TRACK/FOLDER SEARCH KNOB
Turning this knob will let you search either folders and tracks. The track and folder will be shown in the LCD. Turn the knob to scroll
backward and forward through tracks and folders. Pushing this knob, you can see the track menu, i.e. Artist, Track Title, Genre, and Track
Bit Rate.
29. FOLDER BUTTON
The Folder button has two function. The button is used to toggle the TRACK/FOLDER SEARCH KNOB(28) between track and folder
search. The Folder LED will glow when your in Folder search. The button is also used to record your desired music to the system memory
for DEMO play.
30. SOURCE SELECT BUTTON
Press this button to toggle between the USB port or SD Card slot. The button can only be used when the fixture is pause mode.
31. CUE
Pressing the CUE button during playback immediately pauses playback and returns the track to the last set cue point The red CUE LED
will glow when the unit is in cue mode. The LED will also flash every time a new CUE POINT is set. The CUE button can be held down to
momentarily play the track. When you release the CUE button it instantly returns to the CUE POINT. You can also tap the CUE button to
create a BOP EFFECT.
32. PLAY/PAUSE BUTTON
© Copyright LOTRONIC 2014 SYMBOL 250
BSTDJ.COM
Page 9