Intended Use; Scope Of Delivery; Electrical Voltage; Potentially Explosive Atmosphere - Buhler Smartline Notice De Montage

Smartline
1 Introduction
This quick guide will assist you in starting up the unit. Follow
the safety notices or injury to health or property damage may
occur. Carefully read the original operating instructions in-
cluding information on maintenance and troubleshooting
prior to startup. These are located on the included CD and on-
line at
www.buehler-technologies.com
Please direct any questions to:
Bühler Technologies GmbH
Harkortstraße 29
40880 Ratingen
Germany
Tel.: +49 (0) 21 02 / 49 89-0
Fax: +49 (0) 21 02 / 49 89-20
These operating instructions are a part of the equipment. The
manufacturer reserves the right to change performance-, spe-
cification- or technical data without prior notice. Please keep
these instructions for future reference.

1.1 Intended Use

The portable sample gas probe is intended for use in gas ana-
lysis systems in industrial applications. It is particularly suit-
able for use with mobile sample gas conditioning.
Portable sample gas probes are among the main components
in a gas conditioning system.
• Before using the device, verify the listed technical data
meet the application parameters.
• Therefore also note the related drawing in the data sheet
in the appendix.
• Further check if all contents are complete.
Please refer to the nameplate to identify your model. In addi-
tion to the job number it also contains the item number and
model designation.
When connecting, please note the specific values of the
device, and the correct version when ordering spare parts.
When using the Smartline portable probe for a different pur-
pose than originally intended, please consult our technical ad-
visers to determine the suitability of the probe.
Unauthorised misappropriation is prohibited. Any modifica-
tion of the portable probe will compromise operating safety
and automatically void the manufacturer warranty.

1.2 Scope of Delivery

• Portable probe model Smartline
• Product documentation
Attached and included accessories are listed separately in the
order.
2 General hazard warnings
The equipment must be installed by a professional familiar
with the safety requirements and risks.
Be sure to observe the safety regulations and generally applic-
able rules of technology relevant for the installation site. Pre-
vent malfunctions and avoid personal injuries and property
damage.
BX464002 ◦ 08/2020
The operator of the system must ensure:
• Safety notices and operating instructions are available
and observed,
• The respective national accident prevention regulations
are observed,
• The permissible data and operational conditions are
maintained,
• Safety guards are used and mandatory maintenance is
performed,
• Legal regulations are observed during disposal,
• compliance with national installation regulations.
DANGER

Electrical voltage

Electrocution hazard.
a) Disconnect the device from power supply.
b) Make sure that the equipment cannot be reconnected to
mains unintentionally.
c) The device must be opened by trained staff only.
d) Regard correct mains voltage.
DANGER
Toxic, corrosive gases
The measuring gas led through the equipment can be hazard-
ous when breathing or touching it.
a) Check tightness of the measuring system before putting
it into operation.
b) Take care that harmful gases are exhausted to a save
place.
c) Before maintenance turn off the gas supply and make
sure that it cannot be turned on unintentionally.
d) Protect yourself during maintenance against toxic / cor-
rosive gases. Use suitable protective equipment.
DANGER

Potentially explosive atmosphere

Explosion hazard if used in hazardous areas.
The device is not suitable for operation in hazardous areas
with potentially explosive atmospheres.
Do not expose the device to combustible or explosive gas mix-
tures.
3 Transport and storage
Only transport the product inside the original packaging or a
suitable alternative.
The equipment must be protected from moisture and heat
when not in use. They must be stored in a covered, dry and
dust-free room at a temperature between -20 °C to 50 °C (-4 °F
to 122 °F).
Bühler Technologies GmbH 7