General Maintenance - Ryobi CJS-180L Manuel D'utilisation

GB
FR DE ES IT
OPERATION
ANGLE CUTTING (Bevel Cutting) (Fig.10-
Fig.11)
Bevel cutting angles may be adjusted from 0° to 45° right
or left. Angles for cuts from 0° to 45° in 15° increments
are marked on a scale on both the left and right side
of the base. Notches on the rear of the base provide
positive stops at each of the above mentioned 15°
increments. A protractor is recommended when accurate
cuts are required.
Remove battery pack.
Q
Using the 3 mm. hex key provided, loosen the base
Q
pivot screws until the base can be moved.
Slide base backward until base pivot screws can
Q
move freely in slots in base.
Align the mark, on the base, of the desired angle with
Q
the edge of the motor housing.
Once the desired angle is reached, slide base forward
Q
until tab on motor housing aligns with the appropriate
notch on rear of base.
NOTE: When making a set-up for accurate cuts with
a protractor, or for angles other than the preset 15°
increments, the positive stop notches on the rear of the
base are not used.
Tighten the base pivot screws securely.
Q
Return hex key to storage compartment.
Q
Replace battery pack.
Q
NOTE: The wide slot in the base must be used when
making bevel cuts, scroll cuts, plunge cuts, and when
cutting metal.
PLUNGE CUTTING(Fig.12)
WARNING:
To avoid loss of control, broken blades, or
damage to the material being cut, always use
extreme caution when making plunge cuts. We
do not recommend plunge cutting on materials
other than wood.
Mark the line of cut clearly on the workpiece.
Q
Set the cutting angle at 0°.
Q
Tilt the saw forward so that it rests on the front edge
Q
of the base and blade will not come in contact with
the workpiece when the saw is turned on.
Make sure the blade is inside the area to be cut.
Q
Using high speed, start the saw and slowly lower the
Q
blade into the workpiece until the blade cuts through
the wood.
961075062-03(CJS-180L)_EU.indd Sec1:4 961075062-03(CJS-180L)_EU.indd Sec1:4
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
Continue lowering the blade into the workpiece until
Q
the base rests flat on the work surface, then move the
saw forward to complete the opening.
WARNING:
Use of controls or adjustments or performance
of procedures other than those specified herein
could result in hazardous radiation exposure.
ADJUSTING THE LASER(Fig.13)
The laser can be realigned by adjusting the two screws
located in the front of the saw. The top screw moves the
laser beam laterally from left to right. The bottom screw
moves the laser beam in a rotational direction.
NOTE: Draw a pencil line on scrap workpiece parallel to
the long edge of the base as a straight line guide to aid in
the adjusting process.
Remove the blade from the saw.
Q
Turn laser on.
Q
Rest base of saw on scrap workpiece.
Q
Adjust screws as necessary.
Q
Since blade thicknesses vary, always make a trial cut
Q
in scrap workpiece to ensure an accurate cut.
Check for proper alignment.
Q
Repeat as necessary until laser is aligned.
Q
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a
hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses
with side shields during power tool operation or
when blowing dust. If operation is dusty, also
wear a dust mask.
WARNING:
To avoid serious personal injury, always remove
thebattery pack from the tool when cleaning or
performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
4
LT EE HR SI SK GR
1/5/10 1:37:43 PM 1/5/10 1:37:43 PM
TR