Ryobi CJS-180L Manuel D'utilisation page 6

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 10
GB
FR
DE
ES
IT
OPERATION
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second issufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses
with side shields when operating tools. Failure
to do so could result in objects being thrown into
your eyes, resulting inpossible serious injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Cutting wood surfaces
Q
Cutting thin sheet metal
Q
Cutting plastics and laminates
Q
TO INSERT BATTERY PACK(NOT INCLUDED)
Fig.2
Lock the switch trigger by releasing it all the way.
Q
Place the battery pack on the tool.
Q
Make sure the latches on each side of the battery
Q
pack snap into place and the battery pack is secured
on the tool before beginning operation.
CAUTION:
When placing battery pack in the tool, be sure
raised rib on battery pack aligns with the grooves
in the saw and latches into place properly.
Improper installation of the battery pack can
cause damage to internal -components.
TO REMOVE BATTERY PACK(NOT INCLUDED)
Fig.2
Lock the switch trigger by releasing it all the way.
Q
Depress the latches on the side of battery pack.
Q
Remove the battery pack from the tool.
Q
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
961075062-03(CJS-180L)_EU.indd Sec1:2
961075062-03(CJS-180L)_EU.indd Sec1:2
NL
PT
DK
SE
FI
NO
English
RU
PL
CZ
HU
RO
LV
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
BLADE STORAGE(Fig.3)
The blade storage compartment is located on the back
of the saw. It is convenient for storing extra blades and
storing blades when not in use.
To open: Push the door down with your thumb or
Q
finger. Place blades in blade storage compartment.
To close: Push the door up with your thumb or finger.
Q
WARNING:
Battery tools are always in operating condition.
Therefore, switch should always be locked when
not in use or carrying at your side.
LASER GUIDE(Fig.4)
Depress the laser guide switch to generate a red laser
beam on the work surface in front of the saw. Use the
laser to guide the saw along the line of cut.
LOCK-OFF BUTTON(Fig.4)
The lock-off button is located on the handle above the
switch trigger. You must depress the lock-off button in
order to pull the switch trigger. The lock resets each time
the trigger is released.
NOTE: You can depress the lock-off button from either
the left or right side.
SWITCH TRIGGER(Fig.4)
To turn the saw ON, depress and hold lock-off button,
then depress the switch trigger. To turn it OFF, release
the switch trigger.
2
LT
EE
HR
SI
SK
GR
1/5/10 1:37:42 PM
1/5/10 1:37:42 PM
TR

Publicité

Table des Matières
loading

Table des Matières