Digital Jog Break; Jog Memory - Pioneer EFX-1000 Mode D'emploi

OPERATIONS (Digital Jog Break)
1) JET, WAH, PHASE SHIFTER,
RING, ZIP, HUMANIZER, VOCODER
(Jog effect select)
DEPTH
CHARACTER
MIX
Jog dial

Digital Jog Break

Since the digital jog break can continuously change the
parameters of each effect generated by rotating the Jog
dial, the effects can be controlled like a musical instrument.
Further, by using the jog memory function, the continuously
changing effect sound can be stored in memory, and later
played back by pressing one of the JOG MEMORY PLAY
buttons (SINGLE or LOOP).
1. Use the Jog effect select buttons to select the desired
effect.
¶ Select from JET, WAH, PHASE SHITER, RING, ZIP,
HUMANIZER, or VOCODER.
¶ The selected Jog effect button flashes.
¶ See page 14 regarding each effect.
2. Set the DIGITAL JOG BREAK lever switch to ON and
turn the Jog dial.
[DIGITAL JOG BREAK Lever switch operation]
When pushed away from you to the [ON/LOCK] position:
The switch is locked on, so that the effect continues to be
applied even if you remove your hand from the lever. To stop
the effect, return the lever to the middle position [OFF].
When pulled toward you to the [ON] position:
The effect is applied only while the lever is pulled to the [ON]
position; when the lever is released, it returns automatically to
the middle [OFF] position. Use this function when you wish to
alternate rapidly between ON and OFF.
¶ Parameter changes caused by rotating the Jog dial are
indicated on the DIGITAL JOG BREAK METER.
DEPTH dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 1 in
response to DEPTH dial rotation, see pages 14, 15.
CHARACTER dial
Set to the center center indent position for standard effect sounds.
For more information regarding the change in parameter 2 in
response to CHARACTER dial rotation, see pages 14, 15.
22
<DRB1368>
2) DIGITAL JOG BREAK
HOLD
LOOP
SINGLE
Jog memory (M)
MIX dial
Use to adjust the mixing balance of original and effect sounds. Set
to the center indent position for standard effect sounds.
HOLD Function
When the HOLD button is pressed and lit, the effect generated by
the rotation of the Jog dial continues when the dial rotation stops.

Jog Memory

Up to 8 seconds of the digital jog break's jog dial
movement can be stored in memory, and the effect later
played back at a single touch.
1. Use the Jog effect select buttons to select the desired
effect.
¶ Select from JET, WAH, PHASE SHITER, RING, ZIP,
HUMANIZER, or VOCODER.
¶ The selected Jog effect button flashes.
¶ See page 14 regarding each effect.
2. Set the DIGITAL JOG BREAK lever switch to ON to
monitor the effect.
3. Turn the Jog dial while holding down the Jog memory
button (M).
Turning the Jog dial while the M button is held down starts
memory storage. Effects are stored continues for 8 seconds or
until the M button is released. The SINGLE or LOOP button
lights.
¶ When an effect has already been stored in memory
(SINGLE button and LOOP button are lighted), if a new
effect is stored in memory, the previously stored contents
will be overwritten and the effect data will be erased.
4. Press the SINGLE or LOOP button.
¶ When the SINGLE button is pressed, the button flashes and
the stored effect produced by the jog dial movement is
played back one time.
¶ When the LOOP button is pressed, the button flashes and
the stored effect produced by the jog dial movement is
played back repeatedly. Press the LOOP button once again
to stop the effect playback.
¶ Jog dial operation stored in memory can be reproduced
even when the type of effect is subsequently changed.