Lamp Replacement; Overhead Rigging - Briteq BT-2505 Mode D'emploi

ENGLISH
LAMP (RE)PLACEMENT
In case of replacement of the lamp or maintenance, do not open the fixture within 10
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When replacing
parts, please only genuine spare parts.
 Switch off the main supply and unplug the unit.
 Wait for about 15 minutes until the unit has been cooled
down.
 Unscrew the 2 screws on the back of the fixture to open
the lamp compartment (See A on the picture)
 On the inside you will see the lamp socket. Tear the lamp
socket gently out of the lamp compartment.
 Unplug the old lamp. Hold the lamp socket while
unplugging the lamp !
 Hold the lamp socket while pressing the new lamp gently
in the socket.
Attention! Check the label on the backside of the device
or see the technical specifications in this manual to know
which lamp should be used. Never install lamps with a
higher wattage!
 Don't touch the bulb with bare hands! This drastically
shortens the lifespan of the lamp. If you touched the lamp,
clean it with a cloth and a little denatured alcohol. Wipe
the lamp off before installing.
 Put the new lamp back inside the unit. Be sure that the
wires don't touch the lamp.
 Close the lamp compartment with the screws
 Make sure the lamp is located in the center of the reflector for the best spot. Switch the unit on and adjust
lamp position by screws A, B and C, located on the back of the head. ( A on the picture )
 Done!
EXCHANGING/ROTATING GOBOS
ATTENTION: Install the gobos only when the unit is switched off!
Never unscrew the screws of the rotating gobo as the ball bearing will be opened. Repairing
this is very difficult!
 Switch off the main supply and unplug the unit.
 Open the plastic top cover (4screws)
 Locate the gobo wheel and remove the fixation
ring of the gobo you want to change with an
appropriate tool.
 Remove the gobo and insert the new gobo.
 Press the fixation-ring together and insert it in
the front of the gobo.
 Done!
Briteq
®
OPERATION MANUAL
3/69
ENGLISH

OVERHEAD RIGGING

 Important: The installation must be
carried
personal only. Improper installation
can result in serious injuries and/or
damage to property. Overhead rigging
requires
Working
respected,
materials should be used, the installed
device should be inspected regularly
for safety.
 Make sure the area below the installation
place is free from unwanted persons
during rigging, de-rigging and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
HOW TO SET UP THE UNIT
 CONTROL PANEL:
BT250S Briteq
®
out by qualified service
extensive experience!
load limits should be
certified installation
4/69
OPERATION MANUAL
BT250S