Quick DP1 PRINCE Série Manuel De L'utilisateur page 17

POS. DESCRIPTION
10 Bearing
11 Shaft DP1
12 Shaft DP1 D
13 Key 6*6*25
14 Key 6*6*50
15 Oil seal 20*35*7mm
16 Chain guide cover DP1
17 Plastic chain pipe DP1
18 Screw M 4*30 stainless steel
19 Screw M 5*30 stainless steel
20 Screw M 5*40 stainless steel
21 Chian stripper DP1 stainless steel SPMSNDP10000
22 Plug 4*22 stainless steel
23 Screw M 6*12 stainless steel
24 Cover base DP1 stainless steel
25 Insert plastic cover DP1
26 Nut M4
27 Nut M5
Round base DP1
28
anodized aluminium
29 Gasket / jig
30 Sensor
31 Stud
32 Gearbox flange gasket
300/500W
33A Gearbox 500W Quick series
33B Gearbox "Hi Speed" 500W
Quick series
34 Washer
35 Spring washer
36 Nut
37 Screw
38 Geared motor seal
39 Key
40A Electric motor 300W 12V
40B Electric motor 500W 12V
40C Electric motor 500W 24V
41 Flange gasket
42 Motor casing watertight 300/500W PCCCPM040000
43 Poles gasket
electric motor 300/500W
44 Bottom protec cover
electric motor 300/500W
45 Screw
DP1 300/500W - REV001A
www.busse-yachtshop.de | info@busse-yachtshop.de
CODE
MBJ160040000
MSASDP100R00
Quick
MSASDP1D0R00
marine environments. In any case, any salt deposits on the outside
MBH060625X00
must be removed periodically to avoid corrosion and damage to
MBH060650X00
the equipment. The parts where salt may have built up should be
PGPRL2035700
washed thoroughly with fresh water.
PDGCDP100000
PDPSSDP10R01
Once a year, the drum and the gypsy are to be taken apart as fol-
lows:
MBV0430MXVEP
MBV0530MXCE0
DRUM VERSION
MBV0540MXCE0
Use the handle (1) to loosen the bush (2); pull off the drum (3) and
the top clutch cone (5); loosen the fixing screws (20) of the rope/
MBSC04022A00
chain stripper (21) and remove it. Pull off the gypsy (6).
MBV0612MXTSC
NO-DRUM VERSION
SPMSGB0DP1X0
Use the handle (1) to remove the gypsy cover (4); remove the top
PDNC0DP10000
clutch cone (5); loosen the fixing screws (20) of the rope/chain strip-
MBD04MXEN000
per (21) and remove it. Pull off the gypsy (6).
MBD05MXEN000
Clean all the parts removed to avoid corrosion, and grease the shaft
SGMSC0DP1A00
thread (11 or 12) and the gypsy (6) where the clutch cones rest (5).
PGBSDP100000
KNREEDCL0000 Clean all the parts removed to avoid corrosion, and grease the shaft
thread (11 or 12) and the gypsy (6) where the clutch cones rest (5).
MBP080608X00
PGFLRDTG4000
Remove any oxide deposits from the terminals of the electric motor
and the reversing contactor unit; grease them.
SLMR05TG4000
SLMR05TG40HS
MBR08X000000
MBR08XDE0000
MBD08MXEN000
MBV0516MXE00
PGBMR0400000
MBH040415F00
EMF031200000
EMF051200000
EMF052400000
PGGPMFN04000
PGGPMPM04000
PCCPPMFN0400
MBV03916AXCC
MAINTENANCE
WARNING: make sure the electrical power to the motor
is switched off when working manually on the windlass.
Carefully remove the chain from the gypsy or the rope from
the drum.
® windlasses are manufactured with materials resistant to
GB
17