Table des Matières
Publicité
10.1 Guide pour le parcours de la cheminée
Élevez les sections de cheminée horizontales de 1/4 po/pi (21 mm/m)
40 pi
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
8/25/2017
TWO PLACE DECIMAL
FRACTIONAL
1/32"
.015"
DRAWN
THREE PLACE DECIMAL
.005"
MATERIAL
CHECKED
REV.
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
SIZE DWG. NO.
A
46DVA-VCH
OTHERWISE.
FINISH
SCALE
1:5
WEIGHT:
SHEET 1 OF 1
Position 2
30 pi
29 pi
28 pi
27 pi
26 pi
25 pi
24 pi
23 pi
22 pi
21 pi
20 pi
19 pi
18 pi
17 pi
16 pi
15 pi
14 pi
13 pi
12 pi
11 pi
10 pi
9 pi
8 pi
7 pi
6 pi
5 pi
4 pi
3 pi
2 pi
1 pi
0 po
DIMENSIONS ARE IN INCHES
DIMENSIONS ARE IN INCHES
TOLERANCES:
TOLERANCES:
FRACTIONAL
1/32"
DRAWN
FRACTIONAL
TWO PLACE DECIMAL
.015"
TWO PLACE DECIMAL
CHECKED
THREE PLACE DECIMAL
.005"
THREE PLACE DECIMAL
ALL BENDS ARE ASSUMED
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
TO BE 90 UNLESS NOTED
OTHERWISE.
Figure 10.1.01:
OTHERWISE.
20
NAME
DATE
NAME
DATE
DIMENSIONS ARE IN INCHES
DIMENSIONS ARE IN INCHES
TOLERANCES:
TOLERANCES:
DRAWN
8/24/2017
DRAWN
8/24/2017
FRACTIONAL
1/32"
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
TWO PLACE DECIMAL
.015"
CHECKED
CHECKED
THREE PLACE DECIMAL
.005"
THREE PLACE DECIMAL
.005"
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
REV.
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
TO BE 90 UNLESS NOTED
A
DVA 48in Pipe
TO BE 90 UNLESS NOTED
A
FINISH
FINISH
OTHERWISE.
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
OTHERWISE.
SCALE
1:20
WEIGHT:
39,153 po
1 pi à 1 pi et 11.9 po verticalement: un
coude de 90⁰ peut être utilisé.
2 pi à 2 pi et 11.9 po verticalement:
deux coudes de 90⁰ peuvent être
utilisés.
3 pi à 3 pi et 11.9 po verticalement: trois
0 po
coudes de 90⁰ peuvent être utilisés.
NAME
DATE
NAME
DATE
8/24/2017
DRAWN
8/24/2017
1/32"
.015"
CHECKED
.005"
REV.
SIZE DWG. NO.
MATERIAL
A
41-DVT Framing
REV.
SIZE DWG. NO.
A
41-DVT Framing
FINISH
SHEET 10 OF 10
4 pi et plus verticalement: quatre
SCALE
1:50
WEIGHT:
SCALE
1:50
WEIGHT:
SHEET 10 OF 10
coudes de 90⁰ peuvent être utilisés.
Installation
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN
8/24/2017
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
.005"
REV.
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
REV.
DVA 48in Pipe
TO BE 90 UNLESS NOTED
A
DVA 48in Pipe
FINISH
SHEET 1 OF 1
OTHERWISE.
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
Position 1
NAME
DATE
NAME
DATE
DIMENSIONS ARE IN INCHES
DIMENSIONS ARE IN INCHES
DIMENSIONS ARE IN INCHES
TOLERANCES:
TOLERANCES:
TOLERANCES:
DRAWN
8/24/2017
DRAWN
8/24/2017
FRACTIONAL
1/32"
FRACTIONAL
1/32"
FRACTIONAL
TWO PLACE DECIMAL
.015"
TWO PLACE DECIMAL
.015"
TWO PLACE DECIMAL
CHECKED
CHECKED
THREE PLACE DECIMAL
.005"
THREE PLACE DECIMAL
.005"
THREE PLACE DECIMAL
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
REV.
ALL BENDS ARE ASSUMED
MATERIAL
SIZE DWG. NO.
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
A
DVA 48in Pipe
TO BE 90 UNLESS NOTED
A
TO BE 90 UNLESS NOTED
FINISH
FINISH
OTHERWISE.
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
OTHERWISE.
SCALE
1:20
OTHERWISE.
WEIGHT:
Sous la ligne pointillée, le
restricteur doit être enlevé pour
les installations de plus de
2000 pi. Voir Section 18.14.
INTERDIT
•
La hauteur de la cheminée est
mesurée à partir du haut du foyer.
•
Le prolongement de la bride de
clouage n'est pas illustré à des
fins de clarté.
•
Deux coudes de 45⁰ = un coude
de 90⁰.
•
Voir Section 10.5 pour l'utilisation
d'un évent périscopique.
NAME
DATE
DRAWN
8/24/2017
1/32"
.015"
CHECKED
.005"
MATERIAL
REV.
SIZE DWG. NO.
REV.
DVA 48in Pipe
A
DVA 48in Pipe
FINISH
SHEET 1 OF 1
SCALE
1:20
WEIGHT:
SHEET 1 OF 1
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
8/24/2017
DRAWN
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
CHECKED
THREE PLACE DECIMAL
.005"
MATERIAL
ALL BENDS ARE ASSUMED
SIZE DWG. NO.
41
A
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
SCALE
1:50
WEIGHT:
Publicité
Table des Matières
