Safety Instructions; English - DeWalt DW744 Mode D'emploi

Safety instructions

When using Power Tools, always observe the safety regulations
applicable in your country to reduce the risk of fire, electric shock
and personal injury. Read the following safety instructions before
attempting to operate this product.
Keep these instructions in a safe place!
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose Power Tools to humidity. Keep work area well lit.
Do not use Power Tools in the presence of flammable liquids or gases.
3 Guard against electric shock
Prevent body contact with earthed surfaces (e.g. pipes, radiators,
cookers and refrigerators). For use under extreme conditions (e.g. high
humidity, when metal swarf is being produced, etc.) electric safety can
be improved by inserting an isolating transformer or a (FI) earth-leakage
circuit-breaker.
4 Keep children away
Do not let children come into contact with the tool or extension cord.
Supervision is required for those under 16 years of age.
5 Extension cords for outdoor use
When the tool is used outdoors, always use extension cords intended
for outdoor use and marked accordingly.
6 Store idle tools
When not in use, Power Tools must be stored in a dry place and
locked up securely, out of reach of children.
7 Dress properly
Do not wear loose clothing or jewellery. They can be caught in moving
parts. Preferably wear rubber gloves and non-slip footwear when
working outdoors. Wear protective hair covering to keep long hair out
of the way.
8 Wear safety goggles
Also use a face or dust mask in case the operations produce dust or
flying particles.
9 Beware of maximum sound pressure
Take appropriate measures for the protection of hearing if the sound
pressure of 85 dB(A) is exceeded.
10 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees both
hands to operate the tool.
11 Do not overreach
Keep proper footing and balance at all times.
12 Avoid unintentional starting
Do not carry the plugged-in tool with a finger on the switch.
Be sure that the switch is released when plugging in.
13 Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
14 Disconnect tool
Shut off power and wait for the tool to come to a complete standstill
before leaving itunattended. Unplug the tool when not in use,
before servicing or changing accessories.
15 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from the
tool before operating the tool.
16 Use appropriate tool
The intended use is described in this instruction manual. Do not force
small tools or attachments to do the job of a heavy-duty tool. The tool
will do the job better and safer at the rate for which it was intended.
Warning! The use of any accessory or attachment or performance of
any operation with this tool, other than those recommended in this
instruction manual may present a risk of personal injury.
14
17 Do not abuse cord
Never carry the tool by its cord or pull it to disconnect from the socket.
Keep the cord away from heat, oil and sharp edges.
18 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Inspect the tool cords at regular intervals and, if
damaged, have them repaired by an authorized D
Inspect the extension cords periodically and replace them if damaged.
Keep all controls dry, clean and free from oil and grease.
19 Check for damaged parts
Before using the tool, carefully check it for damage to ensure that it will
operate properly and perform its intended function. Check for
misalignment and seizure of moving parts, breakage of parts and any
other conditions that may affect its operation. Have damaged guards
or other defective parts repaired or replaced as instructed.
Do not use the tool if the switch is defective. Have the switch replaced
by an authorized D WALT repair agent.
E
20 Have your tool repaired by an authorized D
This Power Tool is in accordance with the relevant safety regulations.
To avoid danger, electric appliances must only be repaired by qualified
technicians.
Additional safety rules for saw benches
• Do - protect the electrical supply line with a suitable fuse or circuit
breaker.
• Do - make certain the blade rotates in the correct direction and that the
teeth are pointing to the front of the saw bench.
• Do - be sure all clamp handles are tight before starting any operation.
• Do - be sure all blade and arbor collars are clean and the recessed
sides of the collars are against the blade.
• Do - keep the saw blade sharp and properly set.
• Do - keep hands out of the path of the saw blade.
• Do - shut off the power and wait for the saw blade to stop before
servicing or adjusting the tool.
• Do - disconnect the saw from the mains supply before changing the
blade or carrying out maintenance.
• Don't - attempt to operate on anything other than the designated
voltage.
• Don't - use blades larger or smaller than those which are
recommended.
• Don't - force the cutting action. (Stalling or partial stalling of the motor can
cause major damage. Allow the motor to reach full speed before cutting.)
• Don't - cut ferrous metals, non-ferrous metals or masonry.
• Don't - use abrasive wheels.
• Don't - apply lubricants to the blade when it is running.
• Don't - place either hand in the blade area when the saw is connected
to the power source.
• Don't - use any blades other than those specified in this instruction
manual.
• Don't - operate the saw without the guards in place.
• Don't - reach around behind the saw blade.
• Don't - place hands closer than 150 mm from the saw blade while
cutting.
• Don't - use damaged or cracked saw blades.
Residual risks
The following risks are inherent to the use of saws:
- injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
E N G L I S H
WALT repair agent.
E
WALT repair agent
E
en - 2