Bosch GSS 140 A Professional Notice Originale page 12

12 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust box, complete (Microfilter System)*
2 Sanding plate
3 Sanding-sheet clamp
4 Sanding sheet*
5 Release button for front clamping bracket
6 Front clamping bracket
7 On/Off switch
8 Handle (insulated gripping surface)
9 Extraction outlet
10 Latching lever for dust box*
11 Filter element (Microfilter System)*
12 Extraction adapter*
13 Vacuum hose*
14 Perforating tool*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Orbital sander
Article number
Rated power input
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via Velcro backing
— Attachment via clamping
Sanding plate dimensions
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 82 dB(A); Sound power level 93 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745-2-4:
2
a =6.5 m/s , K=2.0 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
1 609 92A 15M | (4.3.15)
0 601 297 0..
W
-1
min
-1
min
mm
mm
mm
mm
kg
(triax vector sum) and uncertainty K
2
.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-4.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
GSS 140 A
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
180
Executive Vice President
12000
Engineering
24000
1.6
115 x 107
Robert Bosch GmbH, Power Tools Division
115 x 140
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 04.03.2015
113 x 105
Assembly
1.4
/II
 Before any work on the machine itself, pull the mains
plug.
Replacing the Sanding Sheet
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 2 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Sanding Sheets with Velcro Backing
The sanding plate 2 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 4, free the Velcro backing
of the sanding plate 2 from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet 4 flush alongside one edge of the
sanding plate 2, then lay the sanding sheet onto the sanding
plate and press firmly.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools