Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Sends
Mon 2
5
4
6
Send
Solo
3
7
2
8
Clip
1
9
0
10
EFX
5
4
6
Send
Solo
3
7
2
8
Clip
1
9
0
10
Aux
5
4
6
Send
Solo
3
7
2
8
Clip
1
9
0
10
+10
+7
Solo Mode
+4
+2
PFL
0
PFL
AFL
-2
Channel
Set
-4
-7
-10
-20
-30
-40
VU Meter
Headphones
Level
5
4
6
3
7
2
8
1
9
0
10
Mono OUT
Use Zone/Sub
Switch, located
on main panel,
to Configure
Output
Active
Phantom +48V
6
Master Controls
42. Media In and Out Master Controls and Clip LEDs
The Media In and Out Master controls regulate the input and output levels at their
respective Media In and Media Out jacks. Reduce the level of the appropriate Media In
master control when the Clip LED illuminates continually.
43. Mon 1 and Mon 2 Send Controls, Solo and Clip LEDs
The Mon 1 and Mon 2 Send controls regulate the level of their respective monitor bus-
ses going to the Mon 1 and 2 Out jacks. The Solo buttons isolate their respective moni-
tor mixes through the headphones and the green LEDs indicate that the Solo feature
is active. The red Clip LED indicates clipping in the buss; reduce the Send level or the
channel Mon 1 or 2 levels to avoid distortion.
44. EFX Send, Solo Controls and Clip LEDs
The EFX Send controls regulate the level of the EFX mix going to the EFX Send jack
and to the Internal Effects processor. The Solo switch isolates the effects mix
through the headphones and the green LED indicates that the Solo feature is active.
The red Clip LED indicates clipping in the buss. Reduce the Send level or the channel
EFX level control to avoid distortion.
45. Aux Send, Solo Controls and Clip LEDs
The Aux Send, Solo controls regulate the level of the Aux mix going to the Aux Send
jack. The Solo Switch isolates the Aux mix through the headphones and the green LED
indicates that the Solo feature is active. The red Clip LED indicates clipping in the buss.
Reduce the Send level or the channel Aux level controls to avoid distortion.
46. Main A/B EQs, Bass and Treble Controls
The Main EQ sliders provide +/-12 dB of bandpass gain regulation at 9 frequencies from
160Hz to 6.3 kHz while Bass and Treble provide +/-15dB of shelving throughout the over-
all low and high frequency ranges.
47. Solo Mode Switch and LEDs
By using the Solo Mode Switches, any
channel in Solo mode is isolated on
the VU-Meter for referencing their
audio levels. By depressing the main
Solo Mode switch, you choose PFL
(pre-fade listen) to help setting the
channel's Gain control for an average
0 dB reading. With the Switch down,
you have after-fader listen mode to
help you check the channel's over-
all signal level as regulated by its
fader. With no channel or other Solo
switches depressed, the meter reads
the Main signal levels.
48. Mono Out Section
The Mono Out section is used prin-
cipally for remote control of subwoofer amplifiers, the L&R Main signal is mixed
down to mono and available at the Mono Out jack. The Level control regulates out-
put and the Sub Switch activates a 120 Hz low-pass filter to facilitate no-crossover
sub operation.
49. EFX and Aux Faders, Mute and Solo Switches and LEDs
The EFX and Aux faders control the amount of internal and external effects as
well as auxiliary input signals being added to the Main mix. The Mute switches
permit introducing effects and auxiliary inputs (e.g. from a second external
160
250
400
630 1.0K 1.6K 2.5K 4.0K 6.3K
+12
+6
0
-6
-12
2000 WAT T STEREO MIXING CONSOLE
+12
+6
0
-6
-12
160
250
400
630 1.0K 1.6K 2.5K 4.0K 6.3K
High
0
+12
+6
-15
dB
+15
Low
0
0
-6
-12
dB
-15
+15
High
0
+12
+6
dB
-15
+15
Low
0
0
-6
-12
-15
dB
+15
Publicité
Table des Matières
