Berker KNX Touch Control Mode D'emploi Et Instructions De Montage page 16

Wecker
Einstellungen System Wecker
z
Wecker
EIN EIN
System
The display area of the activated value is framed by a light border at the
Weckzeit
Weckzeit
bottom and to the right.
Sprache der
– +
–
With editierbaren Texte / change the respective setpoint.
„
07 : 45 07 : 45
In the same way, change the end time
„
Activate the button for each weekday on which this function should be
„
Tastenton
executed within the defined time period.
Einstellungen
The active buttons of the weekdays are displayed in light grey.
With
confirm the entry.
„
The display returns to the previous menu level.
P
If the entries are not confirmed, with
menu level without saving. Using
previously as
Settings
System
Cleaning mode
Settings System Timer
Ventilation 2
P 02 12:00 to 12:05
Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri Sat Sun
Night low. Mon-Fri Night low. Sat-Sun
P 04 22:00 bis 06:00
Mon Tue Wed Thu Fri Sat Sun Mon Tue Wed Thu Fri
Figure 6: Changing a time period
30
+
.
Einstellungen System
System
Sprache Sprache der
System editierbaren Texte
Sprache Sprache der
System editierbaren Texte
Bildschirm Tastenton
Bildschirm Tastenton
the display returns to the previous
the display returns to a page preset
without saving.
Settings System
Alarm Timer
Alarm clock Service
Settings System Timer P 02
– +
Ventilation 3 12 : 00
from
P 03 18:00 bis 18:05
– +
to 12 : 05
Mon Tue Wed Thu Fri Sat Sun
P 05 23:30 bis 09:00
Sat Sun
Setting the alarm (Figure 7)
Press the time display in the top display row (9).
„
Or:
With
„
Mo. 30.06.14 07:22
The display changes to the menu
Einstellungen System
Einstellungen System Press the display surface for hours, then the display surface for minutes in
„
Einstellungen System Wecker
succession.
Wecker Sprache Sprache der
Sprache
System editierbaren Texte
System editierbaren Texte
The display area of the activated value is framed by a light border at the
Weckzeit
bottom and to the right.
Bildschirm Tastenton
–
With
„
07 : 45
Bildschirm
With
„
parameters for the alarm time (Table 2).
Seite 5 Seite 6 Seite 7
With
„
The display returns to the previous menu level.
P
If the entries are not confirmed, with
menu level without saving. Using
previously as
Parameters
Settings
System
Cleaning mode
enter the menu,
Einstellungen System
Einstellungen System Wecker
Wecker Sprache Sprache der
Sprache der
System editierbaren Texte
EIN
EIN
Weckzeit
Bildschirm Tastenton
+
– +
/ decrease/increase the respective setpoint.
07 : 45
Einstellungen System
Tastenton
/ go to the next/previous setting parameter, and in this way, set all
Einstellungen System
Sprache
System
Sprache
System editierbaren Texte
confirm the entry.
Bildschirm
Bildschirm
Einstellungen System Einstellungen System
Sprache Sprache der Sprache Sprache der
System editierbaren Texte System editierbaren Texte
without saving.
Einstellungen System Einstellungen System
Sprache Sprache der Sprache Sprache der
Bildschirm Tastenton Bildschirm
System editierbaren Texte Actions System editierbaren Texte
/
Bildschirm Tastenton Bildschirm
/
/
ON OFF
/
ON OFF
Table 2: Settings in the
Settings System
Alarm
Alarm clock
Figure7: Setting of the alarm time
and then select .
.
Sprache der
editierbaren Texte
Sprache der
Tastenton
Tastenton
the display returns to the previous
the display returns to a page preset
Tastenton
Settings
, after 5 s ... 2 h
Tastenton
(gradual)
, after 1 min, 2 min, ...
menu
Settings System Alarm clock
Alarm clock
ON
Timer
Alarm time
–
Service 07 : 00
z
+
31