SKIL MASTERS 2108 Notice Originale page 6

MAINTENANCE / SERVICE
• Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on
www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
• The battery must be kept separate from the natural
environment and should not be disposed of as normal
domestic waste (symbol 9 will remind you of this when
the need for disposing occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
CE DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60 335, EN 60 745,
EN 55 014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 98/37/EC (until
Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009 on)
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
09 SKIL Europe BV
NOISE/VIBRATION
• Measured in accordance with EN 60 745 the sound
pressure level of this tool is <70 dB(A) (standard
deviation: 3 dB) and the vibration ✱ m/s² (hand-arm
method; uncertainty K = 1.5 m/s²)
✱ when screwdriving <2.5 m/s²
✱ when drilling in metal <2.5 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in
EN 60 745; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
A. v.d. Kloot
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Perceuse/visseuse sans fil
INTRODUCTION
• Cet outil est conçu pour le perçage dans le bois, le
métal, la céramique et les matières plastiques; les outils
avec réglage électronique de la vitesse et rotation à
droite/à gauche sont également appropiés pour le
vissage et le fi letage
• Lisez et conservez ce manuel d'instructions 3
SPECIFICATIONS TECHNIQUES 1
Couple max. vissage dur suivant ISO 5393: 25 Nm
ELEMENTS DE L'OUTIL 2
A Interrupteur de marche/arrêt et réglage de vitesse
B Voyant du chargeur vert
C Anneau pour réglage du couple
D Position de verrouillage (anneau)
E Commutateur pour inverser le sens de rotation
F Eclairage
G Fentes de ventilation
H Chargeur
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur les
personnes. Conservez tous les avertissements et
toutes les instructions pour pouvoir s'y reporter
ultérieurement. La notion d'"outil électroportatif" dans les
avertissements se rapporte à des outils électriques
raccordés au secteur (avec câble de raccordement) et à
des outils électriques à batterie (sans câble de
raccordement).
1) SECURITE DE LA ZONE DE TRAVAIL
a) Maintenez l'endroit de travail propre et bien éclairé.
Un lieu de travail en désordre ou mal éclairé augmente
le risque d'accidents.
9
2108