Pentatech DVT67 Mode D'emploi page 37

SNAP SHOW - view/delete snapshots
!
By pressing the and
the snapshots.
!
To delete the snapshot currently shown on the screen, press the
menu button [9]. When the symbol appears, confirm by
pressing the menu button
!
To delete all the snapshots saved on the mobile unit, press the
door release button
button . (If you don't want to delete the snapshot, press the
button
[10].)
Notes:
#
All snapshots are saved to the integrated ring memory. A
maximum of 75 snapshots can be saved. When the ring memory is
full, the oldest snapshots are overwritten automatically.
#
At the top left of the snapshot you can see the outdoor station
camera from which it was saved (#1 or #2), what number
image you are looking at and the total number of images (e.g.
014/089). The date and time at which the snapshot was saved are
shown at the bottom in the centre.
Factory setting: Restoring the factory settings deletes all the
snapshots
DATE AND TIME
!
By pressing the and
hours, minutes (e.g. 21:04), month, day and year (e. g. 06 - 22 -
2020) in succession.
!
Pressing the and buttons changes the figure.
Notes:
#
The setting must be correct to get the exact date and time stamp on
the saved snapshots.
#
After disconnecting and reconnecting the monitor or after a change
of battery, the date and time must be reset.
Factory setting: not changed on reset
DOOR SET. - Volume/duration of the ring tone on the outdoor station /
duration of the door release
Notes:
#
When using two monitors, the settings for the outdoor station must
be the same.
#
When using two outdoor stations, the settings apply to both.
Volume Setting for the ring tone volume on the outdoor
station (1 to 9 bars)
Factory setting: 5 bars
Ring Time (s) Setting for the duration of the ring tone on the
outdoor station between 0 and 15 seconds. A
setting of 0 seconds means that the ring tone is
switched off.
Factory setting: 1 second
buttons [8], you can scroll through
again.
[11] and confirm by pressing the menu
buttons [8], you can change the
Unlock Time (s) Setting for the duration of the door release relay
activation between 1 and 9 seconds
Factory setting: 3 seconds
LANGUAGE
Setting for the screen language (English, Dutch, Polish, German,
French, Italian, Portuguese, Spanish, Russian, Turkish)
The language can be set by pressing the
Factory setting: German
WALLPAPER - background image
Setting for the screen background (choice of 3 images)
Factory setting: Image 1
REGISTER - pairing/deletion of an outdoor station
Notes:
#
When a monitor is paired with an outdoor station, this is indicated
by a green tick after the outdoor station number (no. 1 or
no. 2).
#
The hash # indicates the currently selected channel.
#
A maximum of two monitors can be paired with each doorbell
button. Up to two outdoor stations can be used with one monitor.
!
Move the hash # to the outdoor station required.
To pair another outdoor station (connected to the power supply)
proceed as follows:
#
DVT67 SET (1 doorbell button): Press and hold the pairing
button [27] until you hear a long beep on the outdoor
station (when the outdoor station is battery operated,
three short beeps can be heard).
#
DVT67/2 SET (2 doorbell buttons): press and hold the
pairing button [27] until you hear long beep on the
outdoor station. Then press the doorbell button you wish to
pair.
!
You now have approx. one minute to complete pairing on the
monitor.
!
Press the menu button
monitor emits a beep.
At the outdoor station and at the monitor a "plop" sound can
be heard and the start screen appears again.
To delete a door intercom
!
press the menu button [9]
!
when the symbol appears, confirm by pressing the menu
button again. (If you don't want to delete the channel,
press the button [10].)
Factory setting: outdoor station paired (channel 1)
VERSION
The top two lines indicate the software version of the monitor; below
that is the version of door intercom #1 and (if present) #2.
and buttons [8].
[9] and select the channel. The
GB - 37