Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
#
The strength of the incoming wireless signal is displayed by the
symbol
on the top right of the camera image on the screen
[2]. The bars next to the antenna symbol indicate the strength.
#
A symbol on the top left of the camera image on the screen
indicates whether the door intercom showing the camera image is
being supplied with power by the power supply unit (
batteries (
) .
#
If there is a ring on the intercom and a snapshot is saved but the
conversation is not accepted on a monitor, a new snapshot is
indicated by the flashing red
screen. As soon as the "Snap Show" menu item is selected, the
symbol disappears.
#
Transmission of sound is only available while the talk function is
activated.
11.2 Switching on the outdoor station camera image
manually
!
Press the
button
[10] on the monitor [1] that is switched on.
!
With only one paired outdoor station, its camera image appears
automatically; with two paired outdoor stations, use the and
buttons [8] to select the outdoor station required, and confirm
by pressing the menu button
As long as the camera image is visible, the following options are
available:
!
To take a static image and save it on the monitor, press the
button
[10]
; the
!
By pressing the talk button
function: either the sound from the microphone [21] on the
outdoor station can be heard over the loudspeaker [7] on the
monitor or the sound from the microphone [15] on the monitor
can be heard over the loudspeaker [18] on the outdoor station in
alternation (intercom function).
The talk function can be ended by pressing the on/off button
[13]; otherwise, it ends automatically after approx. 45
seconds, the start screen appears again and the screen goes off
after approx. 20 seconds.
!
Pressing the door release button
door release, the start screen appears again and the screen
switches off after approx. 20 seconds.
!
To switch the camera off again, press the on/off button
otherwise, this happens automatically after approx. 45 seconds,
the start screen appears again and the screen switches off after
approx. 20 seconds.
Note:
When operating the outdoor station with batteries, it is
not possible to switch the camera image on manually
the outdoor station is supplied in
receive any signals from the monitor, only "Monitor" appears on the
black screen. (In energy-saving mode, the camera image is displayed
only when the ring button [25] is pressed).
symbol at the top left of the
[9].
The camera image appears.
symbol appears briefly.
[12], you can activate the talk
[11]
activates a connected
energy-saving mode
. It cannot
If you still wish to be able to switch the camera image on manually,
you have to switch the outdoor station to
(please note: in this case, the batteries in the outdoor station will
discharge significantly more quickly):
!
Press the pairing button [27] on the outdoor station until you hear
) or by
a
long beep
!
Press the pairing button a second time until you hear
beeps
.
To return to energy-saving mode,
!
press the pairing button [27] on the outdoor station until you hear
three short beeps
!
Press the pairing button a second time until you hear
12. Optional addition of a DVT67M
monitor, a mobile unit DVT60M
and/or a DVT60T / DVT60T2 outdoor
station
DVT67 SET
The monitor of the DVT67 SET has already been paired with the
outdoor station on channel No. 1. A maximum of
one mobile unit and/or one more outdoor station
the existing system DVT67 SET.
To establish a wireless connection between a DVT60T outdoor station
and a DVT67M monitor, pair them as follows:
!
The outdoor station and monitor must both have a power supply
and the monitor must be switched on.
!
Press any button [8/9/10/11/12/13] on the monitor to make
the start screen appear.
!
Press the menu button
!
Scroll through the menu with the
reach "Register" and press the menu button
can select between outdoor station of the set (channel no. 1) or a
second outdoor station (channel 2).
!
Move the hash # to the channel you require by pressing [8]:
#
To connect an additional monitor or a mobile unit to the
outdoor station of the DVT67 SET, select channel No. 1.
#
To connect a monitor to a second outdoor station, select
[13];
channel No. 2.
!
Press and hold the pairing button [27] on the outdoor station
until you hear a long beep (when the outdoor station is battery
operated, three short beeps can be heard). Now you have got one
minute to do the pairing.
!
Press the menu button [9] and select the channel. The monitor
as
emits a beep, and the outdoor station and the monitor make a
"plop" sound as confirmation that pairing has been successful.
The start screen appears again on the monitor.
energy consumption mode
.
.
[9]
to open the menu.
and buttons [8] until you
three short
a long beep
.
one more monitor, or
can be connected to
to confirm. You
GB - 35
Publicité
Table des Matières
