Noise suppressor check
Let the noise suppressor cool down before any
servicing.
The spark catcher must be checked every 100
hours of operation to make sure it works perfectly.
•
Remove the four bolts and the cover.
•
Now remove the three 6-mm bolts (pic. 9/1), then the
noise suppressor (pic. 9/2), spark catcher (pic. 9/3) and
sealing (pic. 9/4).
•
Clean the spark catcher (pic. 9/3) by a steel brush.
Check the noise suppressor sealing (pic. 9/4) and spark
catcher for any holes and cracks. If the spark catcher or
sealing is damaged, it must be replaced.
•
Refit the parts in a reversed order.
Refuelling
Never refuel when the appliance is running. After using the
appliance, let it cool down for at least 5 minutes before
refuelling.
Fuel: Unleaded petrol
Never smoke near the appliance and fuel. Never refuel near
sparks, flames or open fire.
Inspections and servicing plan
Only a regularly serviced and treated appliance may be a satisfactory aid. Insufficient servicing and maintenance may lead to
unexpected accidents and injuries.
Time interval
Every time the appliance is to be
used
Every 3 months / 50 hours of
operation
After 1 month and then after 6
months
Every 6 months
Every 12 months
Failure - cause - removal
Failure
Cause
Is there a sufficient amount of fuel in the
tank?
Is the engine control switch on?
Engine not starting
Is there a sufficient amount of oil in the
engine?
Is the spark plug all right?
Is the fuel tank cap ventilation lever open?
No voltage in the DC
Is the DC circuit protection on?
outlet
Ignition not all right.
Inappropriate fuel
Engine running
irregularly
Is the overload indicator on?
Appliance not working
Description
•
Check the engine oil level
•
Check whether the fuel hose has no cracks or other damage. Replace it if necessary.
•
Check the air filter
•
Check the Bowden starter. Replace it if necessary.
•
Check for any holes in the exhaust system. Seal or replace it if necessary.
•
Check the noise suppressor and clean or replace it if necessary
•
Check the spark plug state, adjust the distance and clean it
•
Clean the air filter or replace it if necessary
•
Check the engine oil
•
Clean the fuel tap and filter and replace them if necessary
•
Check the bolts and couplers and replace them if necessary
•
Check the distance of valves and adjust it if necessary (cool engine only)
•
Check the cooling fan
17
Important: remove any cables
•
Open the fuel tank cap (pic. 1/2 or 2/2).
•
Add carefully fuel to the filling opening.
•
At all times, refuel the tank not more than up to
the maximum marking (pic. 11).
•
Refit the cap to the filling opening.
Service
Any technical questions? Complaint? Do you need spare
parts or operation manual?
Go to our website www.guede.com and the section Service
will help you quickly and without bureaucracy. Please, help us
to help you. In order to identify your device in case of complaint,
please indicate serial number, order number and year of
manufacture. All information is available on the product label.
To have all information always at hand, put them down.
Serial number:
Order number:
Year of manufacture:
Phone:
+49 (0) 79 04 / 700-360
Fax:
+49 (0) 79 04 / 700-51999
E-Mail:
support@ts.guede.com
Removal
Make sure there is a sufficient amount of fuel in the
tank.
Turn the engine control switch on
Add some oil (SAE 10W-30)
Clean the spark plug and adjust the distance of electrodes
Open the fuel tank cap ventilation lever
Switch the DC circuit protection on
Clean the spark plug and adjust the distance of electrodes
Make sure the appropriate fuel has been used
Check the electric device or appliance for any defects:
- Replace the electric device or appliance
- Have the electric device or appliance repaired in an electric
shop.