Husqvarna DM 406 H Manuel D'utilisation
  1. Manuels
  2. Marques
  3. Husqvarna Manuels
  4. Perceuses
  5. DM 406 H
  6. Manuel d'utilisation
Husqvarna DM 406 H Manuel D'utilisation

Husqvarna DM 406 H Manuel D'utilisation

Masquer les pouces Voir aussi pour DM 406 H:
Table des Matières

Publicité

Liens rapides

Télécharger ce manuel
GB
Operator´s manual
Please read the operator's manual carefully and make sure you
understand the instructions before using the machine.
Manual de instrucciones
E
Lea detenidamente el manual de instrucciones y asegúrese de
entender su contenido antes de utilizar la máquina.
Bedienungsanweisung
D
Lesen Sie die Bedienungsanweisung sorgfältig durch und machen Sie
sich mit dem Inhalt vertraut, bevor Sie das Gerät benutzen.
Manuel d'utilisation
F
Lire attentivement et bien assimiler le manuel d'utilisation avant
d'utiliser la machine.
DM 406 H
HUSQVARNA CONSTRUCTION PRODUCTS
EN ES DE FR

Publicité

Table des Matières
loading

Manuels Connexes pour Husqvarna DM 406 H

Sommaire des Matières pour Husqvarna DM 406 H

  • Page 1 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Manual de instrucciones DM 406 H Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.
  • Page 3 Read all the operating Always use eye and ear Read, understand and follow instructions before using or all warnings and instructions protectors when using the carrying out service procedures in these operating instructions machine. on the machine. and on the machine. Leer el manual de Leer, comprender y observar Para utilizar la máquina, usar...

  • Page 4: Table Des Matières

    Index General safety instructions ......................3 What is what? ..........................5 Presentation..........................6 Connections ..........................0 Operation ............................  Maintenance ..........................6 Compliance with EU directives ....................8 Sommaire Instrucciones generales de seguridad ..................3 Componentes de la máquina ......................5 Presentación ..........................

  • Page 5: General Safety Instructions

    ¡advertenCIa! no está permitido efectuar modificaciones de la versión original del motor de taladro por ningún concepto sin la autorización de husqvarna Construction Products aB. Las modificaciones no autorizadas comportan riesgo de daños personales e incluso peligro de muerte.

  • Page 6: Allgemeine Sicherheitshinweise

    . Bei Arbeiten mit dem Bohrmotor stets Augen- und Gehörschutz tragen. 3. Keine Hydraulikschläuche lösen, solange die Stromversorgungseinheit noch nicht unterbrochen und der Motor ganz zum Stillstand gekommen ist. warnUng! Ohne die Zustimmung von husqvarna Construction Products aB dürfen unter keinen Umständen veränderungen an der Originalausführung des Bohrmotors vorgenommen werden.

  • Page 7: What Is What

    Fig.  f. Mechanical gear control What is what? g. Locking screw a. Pressure hose connection h. Spindle b. On/off lever Coolant connection c. Speed table Return hose connection d. Hydraulic motor control e. Oil plug f. Mando del reductor mecánico Componentes de la máquina g.

  • Page 8: Presentation

    DM 406 HL access to six different spindle speeds with increasing Husqvarna drill motor DM 405 HH/ DM 406 HL is a torque at lower speed. It is possible to alternate between hydraulic drive unit for drill bits. This unit is intended for the three motor speeds when drilling.
  • Page 9 Gewicht ___________________________ 6 kg Rahmen Maximaldruck ______________________ 40 bar Maximaler Durchfluss ________________ 40 l/min Für den Husqvarna Bohrmotor DM 405 HH/ DM 406 HL Empf. Maximaldurchmesser kann z. B. der Husqvarna Rahmen DS 500 verwendet der Bohrkrone _____________________ 650 mm werden.

  • Page 10: Bedienelemente

    Fig. 5 Fig. 6 Speed table Actuators The speed table is placed over the control for the Locking screw, mechanical gear hydraulic motor. It indicates the position for the on/off By unscrewing the locking screw it is possible to adjust lever and different speeds at different settings of the the gear control.
  • Page 11 Fig. 8 Fig. 9 Mechanical gear control On/off lever The drill motor is equipped with a mechanical gear, which The on/off lever starts or stops the rotation. Turn the lever is adjusted with the gear control. The control is pulled to position  to start the rotation.

  • Page 12: Raccordements

    Fig. 0 Fig.  Connections Hydraulic motor control The control controls the speed of the drill motor. Position Coolant connection I indicates the lowest speed and position III the highest. The coolant used to cool the drill bit is connected here. The speed can be adjusted during operation.
  • Page 13 Fig.  Fig. 3 Hydraulic hose connections Thread adapter/Wear adapter The pressure hose and return hose are connected here. The thread adapter is used when a drill bit with CR8 Use quick couplings with a coupling body of 3/8" and /" thread is to be fitted on the spindle with 1 1/4"...

  • Page 14: Utilisation

    Fig. 4 Fig. 5 Operation Oil plug The drill motor is fitted with an oil plug, which is placed on Connection of hoses the underside of the drill motor. This plug is unscrewed when the oil is to be changed. The oil plug has a magnet .
  • Page 15 Fig. 6 Fig. 7 4. Connect the coolant hose. Select mechanical gear . Unscrew the locking screw. nOte! . Pull the control out for smaller drill bit and higher It is important to keep all couplings clean. spindle speed. Press the control in for larger drill bit and lower spindle speed.

  • Page 16: Start Procedure

    Fig. 9 Fig. 8 Fitting of drill bit Start procedure . Set the control in position I for the lowest speed of the Screw tight the drill bit. Carefully check that it is properly fixed. hydraulic motor. Montaje del trépano Procedimiento de arranque .
  • Page 17 Fig. 0 Fig.  . Turn the on/off lever to position  to start the rotation. 3. Carefully feed the drill bit into the concrete so that you obtain good control. . Poner la palanca de activación/desactivación en la 3. Introducir el trépano con cuidado en el hormigón para posición  para arrancar la rotación.

  • Page 18: Entretien

    Maintenance or III to achieve the best cutting. To spare the drill bit On delivery the gearbox is filled with 3 dl of Husqvarna when drilling through reinforcement rods, the speed can Oil 460. Change the oil after one month’s use. After that easily be reduced with the control lever.

  • Page 19: Nettoyage

    Fig. 3 Fig. 4 Oil change Cleaning . Hold a container under the oil plug. Clean the drill motor regularly by wiping it down with a cloth. . Unscrew the oil plug and allow the oil to run out. 3. Place the drill motor with the oil hole upwards. Pour in nOte! 3 dl of new oil, wipe clean the threads and oil plug, and do not use high-pressure wash appliances to clean...

  • Page 20: Compliance With Eu Directives

    Compliance with EU directives Husqvarna Construction Products Sweden AB, Box 098, SE-550 0 Jönköping, Sweden, tel: +46 (0)36-570 60 00, hereby certifies that its drill motor DM 405 HH/ DM 406 HL, having serial numbers 01001 onwards, is manufactured in compliance with the Council’s machinery directive 98/37/EC, low-voltage directive 73/3/EEC and EMC directive 89/336/EEC, including...
  • Page 21 www.husqvarnacp.com 115 04 30-20 2006-12-14...

Ce manuel est également adapté pour:

Dm 405 hhDm 406 hl

Table des Matières