Milwaukee M18 ONESLDP Notice Originale page 12

battery out of use immediately for safety reasons and have
them inspected by a Milwaukee customer service centre
LIGHT INDICATORS
Continuous red Charging
Continuous green Charging is complete
Battery is too hot/cold -
Charging will begin when
Fast fl ashing red
battery reaches correct
charging temperature
Battery charge is pending -
Slow fl ashing red Charging will begin when the
fi rst pack is fully charged
Flashing red/ Damaged or faulty battery
green pack
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
22 ENGLISH
AC OPERATION
Several lamps can be connected together in AC mode.
Please observe the following limits.
230 V
Fuse maximum number of lamps
10 A 6
16 A 10
110 V
10 A 4
16 A 6
MAINTENANCE
For type Y attachments:
If the external fl exible cable or cord of this luminaire is
damaged, it shall be exclusively replaced by the
manufacturer or his service agent or similar qualifi ed person
in order to avoid a hazard.
Caution! Risk of electric shock.
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualifi ed person.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Remove the battery pack before starting any
work on the machine.
Do not stare at the operating light source.
Do not swallow the coin cell battery!
Class II tool.
Tool in which protection against electric shock
does not rely on basic insulation only, but in
which additional safety precautions, such as
double insulation or reinforced insulation, are
provided.
There being no provision for protective earthing
or reliance upon installation conditions.
EU (production code 4000 4589 08)
France (production code 4000 4588 96)
Door opened status -> protection class IP40
EU (production code 4000 4589 08)
France (production code 4000 4588 96)
Door closed status -> protection class IP54
UK (production code 4000 4589 02)
Protection class IP54
Denmark (production code 4000 4588 89)
AC mode -> protection class IP40
Denmark (production code 4000 4588 89)
DC mode -> protection class IP54
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Time-lag fuse 3.15 A
T3.15A
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
23