Operation; Select Tubing And Pump Heads - Masterflex L/S 07519-05 Notice D'utilisation

This section describes the procedures for obtaining the desired performance.

(1) Select Tubing and Pump Heads

Use Tables 1, 2, and 3 to select the tubing, Cartridge, and Pump Head to provide the required single channel flow rate.
CAUTION: Use only tubing/cartridge combinations defined by Tables 1, 2, and 3. Use of other combinations
could cause malfunction or damage to the pump.
Pump
Head
3-Roller
3-Roller
4-Roller
4-Roller
Pump
Head
3-Roller
3-Roller
4-Roller
4-Roller
NOTE: The Pumps operate at the same speed as the drive.
NOTE: Improper tubing stretch could result in reduced flow rate (see LOAD CARTRIDGE section).
Tubing Material
Soft
Silicone (platinum)
Silicone (peroxide)
®
TYGON Silicone
®
C-FLEX (50 A)
Stiff
®
PHARMED BPT (65)
TYGON LFL
®
NORPRENE food (A 60 F)
TYGON lab (R-3603)
NORPRENE (A 60 G)
TYGON fuel (F-4040-A)
PVC
VITON
SANTOPRENE
*Use only specially designed MICROBORE TUBING SETS with Cartridges (Figure 5).
TABLE 1 SMALL CARTRIDGE FLOW RATES—07519-80
Drive
0.89
rpm Units
6 mL/min .44
600 mL/min 44
1 mL/min .074
100 mL/min 7.4
6 mL/min .44
600 mL/min 44
1 mL/min .074
100 mL/min 7.4
TABLE 2 LARGE CARTRIDGE FLOW RATES—07519-70
Drive
®
L/S 14
rpm Units
6 mL/min 1.3
600 mL/min 130
1 mL/min .21
100 mL/min 21
6 mL/min 1.2
600 mL/min 120
1 mL/min .20
100 mL/min 20
TABLE 3 COMPATIBLE TUBING
*MICROBORE TUBING SET
.89, 1.42, 2.06, 2.79
®

OPERATION

MICROBORE TUBING (mm ID)
1.42 2.06
FLOW RATES
1.0 2.2
100 220
.17 .37
17 37
1.0 2.2
100 220
.17 .37
17 37
®
MASTERFLEX L/S
®
L/S 16
FLOW RATES
4.6
460
.76
76
3.8
380
.63
63
MASTERFLEX
(mm ID)
®
L/S 13, 14, 16, 25
X X
X
X
X
X
X
X
X
X
X
X
X
X
8
® ®
MASTERFLEX L/S TUBING
® ®
2.79 L/S 13 L/S
3.8 .30 1.3
380 30 130
.63 .050 .21
63 5.0 21
3.8 .28 1.2
380 28 120
.63 .047 .20
63 4.7 20
®
TUBING
® ®
L/S 25 L/S 17
10 17
1000 1700
1.7 2.8
170 280
8.3 14
830 1400
1.4 2.3
140 230
® ®
L/S TUBING
®
L/S 17
X
X
X
X
14