Sicherheitshinweise - Cooper Crouse-Hinds CEAG eLLK 92 Série Mode D'emploi

Masquer les pouces Voir aussi pour CEAG eLLK 92 Série:
Table des Matières

Publicité

M25 Ex-Blindstopfen
M25 Ex-blanking plug
M25 - 3/4'' Myer Hub
Eaton is dedicated to ensuring that reliable,
efficient and safe power is available when it's
needed most. With unparalleled knowledge of
electrical power management across industries,
experts at Eaton deliver customized, integrated
solutions to solve our customers' most critical
challenges.
Our focus is on delivering the right solution for
the application. But, decision makers demand
more than just innovative products. They turn
to Eaton for an unwavering commitment to
personal support that makes customer success
a top priority.
For more information, visit
www.eaton.com/electrical.

Sicherheitshinweise:

Zielgruppe:
Elektrofachkräfte gem. EN 60079-14 und
unterwiesene Personen.
• Beachten Sie die Anweisungen der
zugehörigen Bertiebsanleitung
3 2216 000 165 bzw 3 2211 000 165 sowie
die Hinweise , die in dieser Anleitung mit
einem (
) gekennzeichnet sind!
Erweiterte technisch Daten
Zulassung:
C
Class I Div 2
Group A.B.C. und D.
Class 1 Zone I AEx de IIC T4
Zündschutzart:
Ex de IIC T4
Zulässige Lampen:
Philips
F17T8/TL 841
GE
F17T8/SPX 41
Osram/Sylvania
F017/ 841
Philips
F32 T8/TL841
GE
F32 T8/SPX41
Osram/Sylvania
F032/ 841
Leitungseinführung: Hubs M25 - 3/4'' NPT
incl. Blindstopfen M25 x 1,5
Achtung!
Das Einführungsgewinde in die Leuchte ist
metrisches Gewinde (M 25 x 1,5)!
Alle nichtbenutzten Einführungen müssen
verschlossen sein!
Zum Verschließen entfernen Sie den nicht-
benutzen Hub und ersetzen ihn durch einen
zugelassenen Blindstopfen!
Die gelbe Schutzkappe dient nur dem
Staubschutz. Sie erfüllt nicht die Explosi-
onsschutzanforderungen und darf nicht in
der Leuchte belassen werden.
Normenkonformität
Die Leuchten entsprechen den Anforderungen
folgender Normen:
C22.2
No. 9
CAN/
E 60079-1
CAN/
E 60079-7
CAN/
E 1241-1-1
IEC 60598-1
UL 60079-0
UL 60079-1
UL 60079-7
UL 60079-11
UL 60079-18
UL 1598
UL 50
IC 60598-1
Cooper Crouse-Hinds GmbH
Neuer Weg-Nord 49
69412 Eberbach
E-Mail: Info-Ex@Eaton.com
www.crouse-hinds.de
© 2015 Eaton
All Rights Reserved
Printed in Germany
Publication No.
3 2216 000 169_a D/E (-) / Auflage
dd
Safety instructions:
For skilled electricians and trained
personnel in accordance with national
legislation, including the relevant stand-
ards and, where applicable, in acc. with
IEC 60079-14 on electrical apparatus for
explosive atmospheres.
• Observe the accessory mounting
instruction 3 2216 000 165 or
3 2211 000 165 as well as the the safety
instructions that are marked with an (
LISTED
US
Additional technical data
Certification:
Explosion category:
Permissible lamps:
Philips
GE
Osram/Sylvania
Philips
GE
Osram/Sylvania
Cable entries:
Attention!
Conformity with standards
The light fittings meet the requirements of the
following standards:
C22.2
CAN/
CAN/
CAN/
IEC 60598-1
UL 60079-0
UL 60079-1
UL 60079-7
UL 60079-11
UL 60079-18
UL 1598
UL 50
IC 60598-1
Changes to the products, to the information contained in this document, and to prices are
reserved; so are errors and omissions. Only order confirmations and technical documentation
by Eaton is binding. Photos and pictures also do not warrant a specific layout or functionality.
Their use in whatever form is subject to prior approval by Eaton. The same applies to
Trademarks (especially Eaton, Moeller, and Cutler-Hammer). The Terms and Conditions of
Eaton apply, as referenced on Eaton Internet pages and Eaton order confirmations.
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
) in these instructions!
LISTED
C
US
Class I Div 2
Group A.B.C. and D.
Class 1 Zone I AEx de IIC T4
Ex de IIC T4
F17T8/TL 841
F17T8/SPX 41
F017/ 841
F32 T8/TL841
F32 T8/SPX41
F032/ 841
Hubs M25 - 3/4'' NPT
incl. blind plug M25 x 1.5
Entry thread in the light fitting is metric
(M 25 x 1.5)!
All unused cable entries must be closed!
To close cable entry remove unused hub
and replace with certified blanking plug!
Yellow protective dust caps in hubs do not
satisfy requirements and shall not be used!
No. 9
E 60079-1
E 60079-7
E 1241-1-1

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ceag ells 08 sérieCeag ellm 92 sérieEllk 92 sérieElls 08 sérieEllm 92 série

Table des Matières