Connecting The Dark Green Wire; Connecting The Starter Disable Relay; Connecting The Parking Light Flasher Relay - Audiovox TSP-575 Guide D'installation Et D'utilisation

8. Connecting the DARK GREEN wire

Trim the DARK GREEN wire to the proper length, strip 1/4 " of the
insulation, and crimp one of the male bullet terminals provided onto the
end of the wire. Plug the bullet terminal onto the receptacle at the bottom
of the hood pin switch.
If you have installed a trunk switch, you should have already routed the
DARK GREEN extension wire to the rear of the vehicle. Crimp the other
bullet terminal onto the end of the extension, and plug it onto the bottom
of the trunk pin switch. You will also need to splice the other end of the
DARK GREEN extension wire to the DARK GREEN wire from the main
harness, and insulate the splice with electrical tape.
PIN SWITCH
MALE BULLET
TERMINAL
GREEN WIRE

9. Connecting the Starter Disable Relay

IMPORTANT ! The relay has been shipped with ( 1 ) BLACK wire loose.
When using the relay to disable the starter, load the BLACK wire into the
relay connector in the location shown in the diagram.
9a. Connect the ORANGE wire from the relay harness to the
ORANGE wire from the main harness. Be sure to insulate this
splice with electrical tape.
9b. Gain access to the wires coming from the ignition switch. Connect
the RED wire from the relay harness to the wire from the ignition
switch that shows + 12 volts on the logic probe when the key is
switched to the " ON or RUN " and " START " positions, and shows
0 volts when the key is switched to the " OFF " position. Be sure
to insulate this connection with electrical tape.
9c. Locate the wire coming from the ignition switch that shows + 12
volts on the logic probe when the starter motor is cranking, and
shows 0 volts when the key is switched to the " OFF ",
" ACCESSORY ", and " ON or RUN " positions. Cut this wire and
try to start the vehicle to verify that the starter motor will not
engage.
Connect the WHITE w/ BLACK stripe wire from the relay harness to one
side of the cut starter wire, and connect the BLACK wire to the other side
of the cut wire.
CAUTION ! Be sure these wires are securely connected, and properly
insulated. If this connection separates, the vehicle will not start, even
when using the ignition key.
ORANGE WIRE-SPLICE TO
ORANGE WIRE FROM
SIREN MODULE HARNESS
CONNECT BLACK
TO ONE SIDE OF
THE START WIRE
CONNECT WHITE w/BLACK STRIPE WIRE
TO OTHER SIDE OF START WIRE
Page 5

10. Connecting the Parking Light Flasher Relay

IMPORTANT ! The relay has been shipped with ( 1 ) BLACK wire loose.
When using the relay to flash the vehicle's parking lights, load the
BLACK wire into the relay connector in the location shown in the
diagram.
10a. Connect the ORANGE wire from the relay harness to the YELLOW
wire from the main harness. Be sure to insulate this splice with
electrical tape.
10b. Gain access to the wires coming from the back of one of the front
parking lamp sockets. Switch the parking lights on, and locate the
wire that shows + 12 volts on the logic probe. Switch the parking
lights off, and verify that this wire now shows 0 volts. Connect the
BLACK wire from the relay socket to this wire, and insulate the
connection with electrical tape.
10c. Connect both the RED wire from the relay socket and the WHITE
w/ BLACK stripe wire from the relay socket to a + 12 volt battery
fused wire ( minimum 15 Amp fuse ) in the vehicle. These wires can
be connected to the positive battery terminal, however when
connecting them to the positive battery terminal, you must add an
in line fuse of at least 15 Amps. Connect one side of the fuse to the
positive battery terminal, and the other side of the fuse to the RED
and WHITE w/ BLACK stripe wires from the relay connector.
ORANGE-SPLICE TO
YELLOW WIRE FROM
SIREN HARNESS
RED WIRE-SPLICE TO
THE IGNITION WIRE
BLACK-SPLICE
TO PARKING
LIGHT WIRE
RED
WHITE/BLACK
+12 VOLT CONSTANT FUSED WIRE