Topcom Twintalker 5400 Manuel D'utilisateur page 5

Twintalker 5400
12.7.1 Changing sub-channels
• Press the
no sub-channel) will blink.
• Use the
channel:
1..38: CTCSS code (1...38)
39..121: DCS code
• Press the PTT - key
Annex B will show all detailed information about the CTCSS and DCS sub-channel codes.
12.8 Making a call
When you press the
channel/sub-channel.
This will indicate that you want to start a conversation.
• Press the
There are 5 different call tones. You can select a call tone in the menu:
• Press the
• Use the
• Press the PTT - key
12.9 Monitor
You can use the monitor function to check for weaker signals in the current channel.
• Press the MON - key 13 to start monitoring.
• If you hold this key for more than 3 seconds, the radio will go into continuous monitoring mode.
• Press the key again to disable the monitor function.
12.10 Channel Scan
Channel scan performs a search for active signals in an endless loop from channel 1 to 8.
Once an active channel is found, the scanning will stop so you can listen to the conversation.
If there is no more activity on the found channel, the scanning will resume after two seconds.
If you press the PTT- key on the found channel, the scan function will end and the radio will remain on this channel.
15
• Press the
• Use the
• Press the
• The scanning will stop once the PTT - key
12.11 VOX
When the optional headset (without PTT-key) is connected, the voice activated transmission function (VOX) can be used.
This way, the user does not need to press the PTT button to start transmitting. The Twintalker 5400 will start transmitting when you
start talking into the microphone of the headset.
• Press the
• Use the
disable VOX. (there are 5 VOX levels)
– Level 1 : Highest sensitive for quite environments
– ...
– Level 5 : Lowest sensitivity for noisy environments
• Press the PTT - key
5
- key : The current selected sub-channel (or "oF" in case of
11
12
- key or the - key to select the desired sub-
(1...83)
14 to confirm
- key 10 you will transmit a call tone to the other users on the same
- key 10
5
- key four times
11
12
- key or the - key to select the call tone
14 to confirm.
5
- key two times
11
12
- key or the - key to select Y for scanning
5
- key to confirm : Scanning will begin
14 is pressed.
5
- key three times
11
- key or the - key to select the VOX level or oF to
12
14 to confirm
12.12 Roger Beep On/Off
After the PTT - key 15 is released, the unit will send out a roger beep to confirm that you have stopped talking.
The Roger Beep can be switched On or Off:
• Press the the
• Use the
Roger Beep
• Press the PTT - key
12.13 Key Beep On/Off
When a key is pressed, a tone can be heard.
The key beep can be switched On or Off:
• Press the
• Use the
key tone
• Press the PTT - key
12.14 Key lock
• Press and hold the
lock function.
When key lock is enabled, the PTT- key
key the will still be operational. All other keys are locked.
13 Warranty
13.1 Warranty period
The devices have a 24-month warranty period. The warranty period starts on the day the new unit is purchased. There is no warranty
on standard or rechargeable batteries.
Consumables or defects causing a negligible effect on operation or value of the equipment are not covered. The warranty has to be
proven by presentation of the original or copy of the purchase receipt, on which the date of purchase and the unit-model are indicated.
13.2 Warranty exclusions
Damage or defects caused by incorrect treatment or operation and damage resulting from use of non-original parts or accessories are
not covered by the warranty.
The warranty does not cover damage caused by outside factors, such as lightning, water and fire, nor any damage caused during
transportation. No warranty can be claimed if the serial number on the units has been changed, removed or rendered illegible. Any
warranty claims will be invalid if the unit has been repaired, altered or modified by the buyer
This product is in compliance with the essential requirements and other relevant provisions of the R & TTE directive
1999/5/EC.
The Declaration of conformity can be found on :
http://www.topcom.net/support/cedeclarations.php
5
- key five times
11
- key 12 or the - key to enable (Y) or disable (n) the
14 to confirm
5
- key six times
11
- key 12 for the - key to enable (Y) or disable (n) the
14 to confirm
10
-key for three seconds to activate/deactivate the key
14 , the volume control-keys, the monitor-key (MON) and the call-
5