Safety Instructions - Walter Surface Technologies SURFOX TURBO Manuel De L'utilisateur

Safety Instructions

WALTER weld cleaning machines are produced in
accordance with applicable standards governing the
manufacture, performance and safety of industrial products.
WARNING: When using these machines, basic safety
precautions should always be observed to reduce the risk of
fire, electrical shocks and personal injuries.
Before using this machine, read all Safety and Operating
Instructions carefully and save this owner's manual for
future reference.
1. Read this owner's manual to familiarize yourself with this
unit's operation, its particular features, applications and
limitations.
2. This unit is equipped with a 3-conductor power cord
and 3-prong electrical plug, it must be connected to a
correspondingly grounded receptacle.
3. Allow a minimum of 8" clearance around the unit to keep
all air openings clear of any obstruction. Free airflow
through the vent openings is required to prevent the unit
from overheating.
4. Keep work area clean and well lit. A cluttered
environment invites accidents. Remove any material that
may be ignited by sparks. Do not use this tool when
flammable liquids or gases are present. Keep handles
clean, dry and free from cleaning solution, oil and
grease. Do not use in rain, damp or wet locations.
5. Keep children and other persons at a safe distance
from the work. Make sure no one is under you when
working in high places. Do not let unqualified persons
handle this machine.
6. When working, always wear appropriate clothing and
safety gear, such as suitable and safety approved
chemical resistant gloves, overalls, safety shoes, etc.
7. Always wear approved safety goggles.
8. During the cleaning process, the wand tip and work
piece can reach very high temperatures, allow to cool
before coming in contact with exposed skin.
9. Avoid inhalation of vapors, use only in well ventilated
areas. Use a respirator, if necessary.
10. All electric shocks can be potentially dangerous.
11. Should you encounter an electrical problem, do not
use the unit until qualified personnel have inspected the
equipment.
12. Never operate the unit with its protective cover removed.
13. Stay alert at all times when handling this unit. Watch
what you are doing. Use common sense. Do not operate
the tool when you are tired. Never leave it running
unattended.
14. Make sure the switch is in its OFF position before
plugging in or when moving the unit to avoid unintentional
starting.
15. Hold the wand firmly. Do not overreach, maintain good
footing and balance at all times.
16. Before use, all parts should be carefully examined to
determine that the unit will operate properly and perform
its intended function.
17. Parts that are damaged or defective should be properly
repaired or replaced by a WALTER Factory Service
Center or a WALTER Authorized Service Center.
18. Do not use the unit if the switch does not turn ON and
OFF.
19. Use only the accessories recommended for this system.
Always check accessories before starting to work and do
not use if damaged.
20. CAUTION: WALTER SURFOX electrolyte weld cleaning
solution contains phosphoric acid and may cause burns
when not handled properly. Avoid skin contact.
First aid Wash affected area with water.
Eye contact Flush with water for 15 minutes lifting eyelids
occasionally. Contact physician if necessary. Ingestion DO
NOT induce vomiting. Rinse mouth, drink plenty of water
and get medical attention. Refer to WALTER product SDS
for complete safety data information.
21. Use only WALTER SURFOX electrolyte weld cleaning
solutions with this unit and NEVER mix it with any other
products.
22. Store solutions in their original containers and in a safe
place, out of the reach of children and other unqualified
persons. Keep container contents clean. Do not reuse
SURFOX electrolyte cleaning solutions.
23. Do not touch the wand tip or work piece while working
or immediately after use, they may be extremely hot and
could cause serious burns.
24. Do not abuse the power cord. Never pull or lift this unit
by its cord or yank to disconnect it from the receptacle.
Keep the cord away from heat, oil and sharp edges.
Inspect the cord periodically, if damaged, have it replaced
by a WALTER Factory Service Center or a WALTER
Authorized Service Center.
25. When not in use, switch OFF and unplug the electrical
cord and air hose. It must also remain unplugged when
replacing cleaning pads and other accessories, while
performing maintenance and before servicing.
26. Store the unit in a dry safe place, out of the reach of
children and other unqualified persons.
Safety Instructions
User's Guide SURFOX TURBO 5