Cleaning, Maintenance And Ordering Spare Parts; Ordering Replacement Parts - EINHELL TE-PL 18/82 Li Traduction Du Mode D'emploi D'origine

1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment be-
fore starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment im-
mediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment. The ingress of water into
an electric power tool increases the risk of an
electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Changing the planing knife (Fig. 9)
Danger! Remove the battery before doing any
work on the tool!
The plane is fi tted with two reversible carbide
knives. Reversible knives have two cutting edges
and can be reversed. The guide slot on the rever-
sible knives ensures the same height setting after
a change. Worn, blunt or damaged knives must
be replaced.
Reversible carbide knives cannot be re-sharpe-
ned.
Undo the three hexagonal screws (18) with the
supplied wrench (12) and use a piece of wood to
push the reversible carbide blade sideways out of
the planing shaft (see Fig. 9).
Anl_TE_PL_18_82_Li_SPK7_USA.indb 14 Anl_TE_PL_18_82_Li_SPK7_USA.indb 14
EN
Clean the knife seat before fi tting. Install the kni-
ves in reverse order. Check that the planing knife
coincides with both ends of the planing shaft.
Always replace both knives to ensure a uniform
chip depth.
Danger! Before you switch on the plane make
sure the knives are installed securely and in the
right place.
Check the correct setting (Fig. 10)
(8) Front base plate (moving plane shoe)
(5) Rear base plate (fi xed plane shoe)
1. Correct setting
Result: Smooth planed surface
2. Notches in the surface
Problem: The cutting edge of the planing knife (or
both planing knives) is not parallel to the height of
the rear base plate.
3. Furrows at the start of the planed surface
Problem: The cutting edge of the planing knife
(or both planing knives) is below the height of the
rear base plate.
4. Furrows at the end of the planed surface
Problem: The cutting edge of the planing knife
(or both planing knives) is above the height of the
rear base plate.
7.4 Replacing the drive belt (Fig. 11-12)
•
The belt should be replaced by a trained ex-
pert.
•
The drive belt (21) must be replaced if it is
worn.
•
Undo the screws (19) and remove the side
belt cover (6).
•
Remove the worn drive belt (21) and clean
the two belt pulleys (20/22).
•
Place the new drive belt on the small belt
pulley (22) and pull the belt onto the large belt
pulley (20) while turning the planing shaft.
•
Ensure that the longitudinal grooves on the
drive belt are in the guide grooves on the
drive wheels.
•
Mount the belt cover (6) and secure it with the
screws (19).

7.5 Ordering replacement parts:

Service
1. If your power tool requires service, con-
tact an authorized Einhell USA dealer or
call the Einhell USA customer service
center at 1-866-EINHELL
- 14 -
31.03.2021 13:53:02 31.03.2021 13:53:02