Intended Use; Technical Data; Before Starting The Equipment - EINHELL TE-PL 18/82 Li Traduction Du Mode D'emploi D'origine

•
Cordless Planer
•
Step depth scale
•
Parallel stop
•
Wrench
•
Original operating instruction with safety in-
formation
Separately available accessories
18V 1.5Ah P-X-C lithium-ion battery
18V 2.0Ah P-X-C lithium-ion battery
18V 2.5Ah P-X-C lithium-ion battery
18V 3.0Ah P-X-C lithium-ion battery
18V 4.0Ah P-X-C lithium-ion battery
18V 5.2Ah P-X-C Plus lithium-ion battery
18V 4-6 Multi Ah P-X-C Plus lithium-ion battery
18V P-X-C Dual Port Fast Charger
18V P-X-C Fast Charger
Explore battery + charger options at
einhellUSA.com

3. Intended use

The cordless planer is designed for planing, reba-
ting and chamfering pieces of wood.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
No-load speed: ....................... 15.000 rpm (min
Planing width:............................... 3
Planing depth: ..................
Maximum rabbet depth: ..................
Weight (Tool only): ........................ 5.3 lbs (2.4 kg)
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Anl_TE_PL_18_82_Li_SPK7_USA.indb 12 Anl_TE_PL_18_82_Li_SPK7_USA.indb 12
EN
)
-1
/ in. (83 mm)
1
4
/ in. to / (0.4-2 mm)
1 5
64 64
/ in. (8 mm)
5
16
- 12 -
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect condi-
tion.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The fol-
lowing hazards may arise in connection with
the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
3. Health damage caused by hand-arm vibra-
tions if the equipment is used over a longer
period or is not properly guided and maintai-
ned.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Warning!
Always remove the battery before making adjust-
ments to the tool.
5.1 Adjusting the chip depth (Fig. 3/Item 1)
You can adjust the chip depth in steps of
/ in. (0.4-2 mm) by turning the setting knob for
5
64
the chip depth (1) .
Turn the setting knob for the chip depth (1) clock-
wise: the chip depth will increase
Turn the setting knob for the chip depth (1) coun-
ter-clockwise: the chip depth will decrease
After fi nishing your work, set the chip depth so
that the knives are lowered and therefore protec-
ted from damage. Turn the setting knob for the
/ in. to
1
64
31.03.2021 13:53:02 31.03.2021 13:53:02