Agilent Technologies Trueform Série Guide D'utilisation Et De Maintenance page 442

Aide-mémoire des commandes Agilent série Trueform
SORTIE
OUTPut[1|2] {ON|1|OFF|0}
OUTPut[1|2]?
OUTPut[1|2]:LOAD {<ohms>|INFinity|MINimum|MAXimum|DEFault}
OUTPut[1|2]:LOAD? [{MINimum|MAXimum}]
OUTPut[1|2]:MODE {NORMal|GATed}
OUTPut[1|2]:MODE?
OUTPut[1|2]:POLarity {NORMal|INVerted}
OUTPut[1|2]:POLarity?
OUTPut:SYNC {ON|1|OFF|0}
OUTPut:SYNC?
OUTPut[1|2]:SYNC:MODE {NORMal|CARRier|MARKer}
OUTPut[1|2]:SYNC:MODE?
OUTPut[1|2]:SYNC:POLarity {NORMal|INVerted}
OUTPut[1|2]:SYNC:POLarity?
OUTPut:SYNC:SOURce {CH1|CH2}
OUTPut:SYNC:SOURce?
OUTPut:TRIGger {ON|1|OFF|0}
OUTPut:TRIGger?
OUTPut:TRIGger:SLOPe {POSitive|NEGative}
OUTPut:TRIGger:SLOPe?
OUTPut:TRIGger:SOURce {CH1|CH2}
OUTPut:TRIGger:SOURce?
Commandes de configuration des impulsions
[SOURce[1|2]:]FUNCtion:PULSe:DCYCle {<pourcentage>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:DCYCle? [{MINimum|MAXimum}]
[SOURce[1|2]:]FUNCtion:PULSe:HOLD {WIDTh|DCYCle}
[SOURce[1|2]:]FUNCtion:PULSe:HOLD?
[SOURce[1|2]:]FUNCtion:PULSe:PERiod {<secondes>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:PERiod? [{MINimum|MAXimum}]
[SOURce[1|2]:]FUNCtion:PULSe:TRANsition[:BOTH] {<secondes>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:TRANsition:LEADing {<secondes>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:TRANsition:LEADing? [{MINimum|MAXimum}]
[SOURce[1|2]:]FUNCtion:PULSe:TRANsition:TRAiling {<secondes>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:TRANsition:TRAiling? [{MINimum|MAXimum}]
[SOURce[1|2]:]FUNCtion:PULSe:WIDTh {<secondes>|MINimum|MAXimum|DEFault}
[SOURce[1|2]:]FUNCtion:PULSe:WIDTh? [{MINimum|MAXimum}]
440 Guide d'utilisation et de maintenance Agilent Série Trueform