Barn Doors; Power Supply - IMG STAGELINE ODC-100/ WS Mode D'emploi

3.2 Barn doors

To reduce the light beam angle, optional barn
doors are available: PARC-100B. Fasten the
barn doors to the front of the spotlight.

3.3 Power supply

When the spotlight has been connected to the
mains, it is switched on. The display will show
the menu item most recently selected and go
out after 30 seconds. As soon as a button
(MENU, UP, DOWN or ENTER) is pressed, the
display will light up again for 30 seconds.
WARNING To prevent damage to your eyes,
never look directly into the light
source for any length of time.
Please note that fast changes
in lighting may trigger epileptic
seizures with photosensitive per-
sons or persons with epilepsy!
3.3.1 ODC-100 / WS
Connect the plug (A) of the cable POWER IN
to the inline jack (B) of the mains cable pro-
vided. Then fasten the nut to secure this con-
nection.
POWER IN A

Mains connection ODC-100 / WS
CAUTION! The cable POWER OUT carries
mains voltage. If no further unit is connected to
the cables POWER OUT and DMX OUT, always
screw the protective covers supplied onto the
inline jacks.
Connect the mains plug to a socket (230 V~/
50 Hz).
Power supply of multiple
ODC-100 / WS spotlights
If multiple ODC-100 / WS spotlights are used, the
units can be interconnected for power supply.
For the time being, do not yet connect the first
unit to a mains socket.
1) Use the inline jack of the cable POWER OUT
to connect the first unit to the plug (A) of the
cable POWER IN of the second unit. Pro-
ceed in the same way to connect the second
unit to the third one etc. until all units have
been connected in a chain.
B
230V~
If the mains connection cables between
the spotlights are too short, use suitable
extension cables, e. g.
ODP-34AC
ODP-34AC / 10
CAUTION! To reduce the risk of cable fire
caused by overload, the total current in the
connection cables must not exceed 10 A.
Therefore, do not interconnect more than 19
ODC-100 / WS spotlights.
2) On the last spotlight, screw the protective
cover supplied onto the inline jack of the
cable POWER OUT. The cable carries mains
voltage!
3) Connect the mains plug of the first spotlight
to a mains socket (230 V~ / 50 Hz).
3.3.2 PARC-100 / WS
For power supply, the unit is equipped with Pow-
ercon ® connections.
CAUTION! Never connect or disconnect a Pow-
ercon plug while voltage is applied. Always
make the Powercon connection before making
the mains connection. When disconnecting,
always disconnect the mains connection before
disconnecting the Powercon connection.
Connect the mains jack POWER IN to a mains
socket (230 V~ / 50 Hz) via the mains cable pro-
vided. Connect the blue Powercon plug of the
cable to the mains jack, and then turn the plug
clockwise until it locks. To remove the plug, pull
back the safety latch of the plug and turn the
plug counter-clockwise.
Power supply of multiple
PARC-100 / WS spotlights
If multiple PARC-100 / WS spotlights are used,
the jack POWER OUT of the first spotlight can
be connected to the mains jack POWER IN of
the second spotlight. For this, a mains cable
with Powercon plugs (NAC-3FCB and NAC-
3FCA) is required. Proceed in the same way to
connect the second spotlight to the third spot-
light etc. until all spotlights have been connected
in a chain. Thus, up to 19 spotlights can be inter-
connected. The jack POWER OUT can also be
used for power supply of other (light effect)
units.
CAUTION! To reduce the risk of fire caused by
overload, the current load of the cables and the
mains plug must not exceed 10 A.
length: 2 m or
length: 10 m
9