Crisper Humidity Control; Chilled Door Bin; Water And Ice Dispensers - Whirlpool T1WG2L Guide D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Crisper Humidity Control

(on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.

Chilled Door Bin

(on some models)
Cool air from the freezer is directed to the refrigerator door bin
directly beneath the vents.
NOTE: The dairy compartment and can rack are not associated
with the Chilled Door Bin feature.
Chilled Door Bin Control
The chilled door bin control is located on the left-hand side of the
refrigerator compartment.
A
A. Chilled door bin control
Turn the control clockwise (right) to reduce the flow of cold air
to the bin and make it less cold.
Turn the control counterclockwise (left) to increase the flow of
cold air to the bin and make it colder.

Water and Ice Dispensers

(on some models)
WARNING
Use a sturdy glass when dispensing ice or water.
Failure to do so can result in cuts.
Depending on your model, your water and ice dispensers may
have one or more of the following features: a rotating water
dispenser faucet and pull-out tray, a special light that turns on
when you use the dispenser, or a lock option to avoid
unintentional dispensing.
NOTES:
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system.
6
Cut Hazard
If your model has a base grille filter system, make sure the
base grille filter is properly installed.
The dispensing system will not operate when the freezer door
is open.
After connecting the refrigerator to a water source, flush the
water system by dispensing water into a sturdy container until
you draw and discard 1.5 gal. (5.4 L) of water, or for
approximately 3 minutes after the water begins dispensing.
The flushing process cleans the water system and clears air
from the lines. As the air is cleared from the lines, water may
spurt out of the dispenser.
Allow several hours for the refrigerator to cool down and chill
water.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The Water Dispenser
IMPORTANT: Dispense enough water every week to maintain a
fresh supply.
To Dispense Water (Standard):
1. Press a sturdy glass against the water dispenser pad OR
place the glass below the water dispenser and press the
WATER button.
NOTE: While dispensing water and for 5 seconds after
dispensing has stopped, the digital display will show how
much water has been dispensed. The default unit is ounces.
To switch to cups or liters, press the UNITS button before
dispensing.
2. Remove the glass OR release the button to stop dispensing.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons. In Custom mode, you can
dispense any amount within a specified range. In Water Bottle
mode, you can dispense pre-set amounts according to the size of
the container.
NOTE: The exact amount of water you select will be dispensed.
Be sure that the container is empty and can hold the entire
volume. If ice is in the container, you may need to adjust your
selection.
1. Press MEASURED FILL until the light turns on. Press
MEASURED FILL again to turn the feature off.
NOTE: The dispenser will automatically turn off Measured Fill
after one minute of inactivity. When Measured Fill is turned off,
any changes you have made will be lost and all defaults will be
restored.
2. Press CONTAINER to change from Custom mode to
Water Bottle mode.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

T2rfwg2T1wg2

Table des Matières