Faderstart; End Of Operation - Omnitronic DMS-1050 Mode D'emploi

You can recall all memorized samples from up to 500 CDs after switching the CD-player off. Therefore, you
have to switch the CD-player on, hold the Sampler/Memory-button and insert the respective CD. The display
shows "Recall" until the loading process is finished.
Playback of memorized samples:
Continuous-mode:
By pressing the Sampler/Memory-button (LED on) and the respective Bank-button, you can recall the
samples memorized via the Sampler/Memory -button. The sample will be repeated until you press the
Sampler/Memory-button again (LED off).
The memorized samples can be played back at any time. If the Sampler/Memory-button is pressed during
the playback of the CD, the sample mixes with the CD-playback. If the Sampler/Memory-button is pressed in
the Pause-mode, the sample alone is being played back. The sample playback-speed can temporarily be
adjusted via the Pitch Bend-buttons.
One-shot-mode:
Press the Sampler/Memory-button until the LED flashes. The current sample is stopped and the player goes
into one-shot-mode. When you press the desired Bank-button now, the sample is only played once.
Press the Sampler/Memory-button again (LED off) in order to leave this mode.
Using temporary samples
The temporary samples on the Bank-buttons remain in the buffer memory if you change the CD without
switching the CD-player off. Please note that these samples are only temporarily available and cannot be
memorized on the new CD. This means, that such temporary samples will be deleted from the buffer
memory when you will switch off the CD-player. However, the original samples can be recalled from the
respective CD using the Recall-function.

6.11 Faderstart

With the DMS-1050, you have the possibility to start the CD-player directly from the mixer. Make sure that
the Relay-socket is connected with the respective socket on the mixer. Additionally, the Audio Out-sockets
have to be connected with the Line-input sockets of your mixer. Please note that the Faderstart-function only
works with the appropriate mixers. Insert the CD and select the desired track (Pause-mode). Start playback
from your mixer.
Please note that the Faderstart-function is a Cue-point Faderstart-function. This means that the CD-player
starts playback after activating the respective channel of the mixer and goes into Pause-mode and returns to
the Cue-point after activating the channel again.
Prerequisites for the Faderstart-operation:
The mixer has to be connected via a 3.5 mm mono jack with the CD-player. For starting the playback, the
jack's positive pin (tip) is to be connected with the audio mass via a short impulse. For pausing the playback,
the jack's negative pin (sleeve) is to be connected with the audio mass via a short impulse. The mixer has to
be equipped with a switch, button or fader that will connect the tip with the audio mass for starting the
playback and the sleeve for pausing the playback when the respective channel is activated.
Relay-function
In the Relay-operation, the device automatically switches to the other player after every track. In this way,
you have the possibility to enlarge the music program by using several CDs.
Possibility 1:
Connect the Relay-sockets of the two CD-players with one another. Choose Single or Continuous via the
SGL/CTN-button. The playback switches from one player to the other.
Example:
Press the Single-button (The display shows "SINGLE") on both CD-players. Start playback of CD1. As soon
as the current track of CD1 is finished, the player automatically starts CD2. The first CD-player goes into
Pause-mode. You can enter a new CD or memorize a Cue-point at the respective player in the Pause-Mode.

6.12 End of operation

Before you switch off the device, please make sure that no CD remains in the player. All memorized Cue-
points, samples and effect-parameters are stored inside the CD-player and can be also be recalled after
switching the CD-player off.
28/56 10602425_V_1_0