Memorizing A Sequence (Loop-Function) - Omnitronic DMS-1150 Mode D'emploi

(4) Cue Scratch-function: Press and hold the Scratch-button until the LED is blinking. The surface of the
scratch-wheel is now activated. When touching the scratch-wheel, the player returns to the cue-point.

6.9 Memorizing a sequence (Loop-function)

With the Loop-function, you can repeat a programmable sequence. Please note that you can only recall this
sequence within one track. If you also wish to insert in other tracks, you need to memorize the sequence as
sample on one of the Bank-buttons.
MEMORIZING LOOP-POINTS
(1) If the In-button is pressed in playback-mode, the CD keeps running and the A-point (starting-point) is
marked. By pressing the Out-button, the B-point (end-point) of the sequence is marked. The player
repeats the sequence between A-point and B-point until you press the Out-button once more.
(2) The starting point and the end point of a sequence can be precisely defined to 1 frame. Activate the
Scratch-function with the Scratch-button. Set the unit into pause-mode and precisely select the A-point
(starting-point) via the Scratch-wheel. The display shows the selected A-point (e.g. 3:42:22). Now either
select the B-point (end-point) via the Scratch-wheel or start playback again. When the end-point is
reached, set the unit to pause again and precisely select the end-point via the Scratch-wheel. The
display shows the selected B-point (e.g. 3:51:11). Press the Out-button and the continuous loop will
start. Press the Loop Out-button again to exit the sequence.
(3) You can repeat the sequence once more if you press the Reloop-button and exit again with the Loop
Out-button.
6.10 Sampler-mode
PLAYBACK OF SAMPLES
(1) By pressing the Sampler-button (LED on) and the respective Bank-button, you can recall a sample for up
to 5 seconds. The sample will be repeated until you press the Sampler-button again (LED off). If the
Sampler-button is pressed during playback of the CD, the sample mixes with the CD-playback. If the
Sampler-button is pressed in pause-mode, the sample alone is being played back. The sample
playback-speed can be temporarily adjusted via the Pitch Bend-buttons. You can choose from two
sample playback modes.
(2) Continuous-mode: The sample will be repeated until you press the Sampler-button again (LED off).
(3) One-shot-mode: Press the Sampler-button until the LED flashes. The current sample is stopped and the
player goes into one-shot-mode. When you press the desired Bank-button now, the sample is only
played once. Press the Sampler-button again (LED off) to return to continuous-mode.
MEMORIZING SAMPLES
With the DMS-1150, you can memorize up to 4 different samples of different tracks and recall them via the
Bank-button.
(1) Define a cue-point as described before. Press the Memory-button (LED on) and the desired Bank-button
in order to memorize the current sample on the Bank-button.
(2) The memorized samples can be overwritten at any time. Please note that the samples can only be
deleted by switching the CD-player off an on again.
(3) You can recall all memorized samples from up to 500 CDs after switching the CD-player off. Therefore,
you have to switch the CD-player on, press the Memory-button (LED on) and insert the respective CD.
The display shows "Recall" until the loading process is finished.
SAMPLE-PITCH AND SAMPLE-VOLUME
The sample-pitch and the sample-volume can be individually adjusted and memorized for each sample.
(1) Press the Sampler-button (LED on) and the respective Bank-button in order to recall the sample.
(2) Press the Hold-button (LED on) in order to hold the parameter-adjustments. If you do not press the Hold-
button, the adjustments are only temporary and the CD-player returns to the memorized settings.
(3) By turning the Parameter Time-control, you can adjust the sample-pitch to SP 1000 (maximum pitch-
adjustment) to SP -1000 (minimum pitch-adjustment).
(4) By turning the Parameter Ratio-control, you can adjust the sample-volume to SV 255 (maximum sample-
volume) to SV 000 (minimum sample-volume).
(5) These temporary settings remain until you switch off the CD-player. To memorize these settings with the
sample, press the Memory-button (LED on) and hold it for one second. This way, the adjusted
parameters can be recalled via the Recall-function.
30/64 10602426_V_1_0.DOC