Introduction; Layout (Fig. 1-19); Scope Of Delivery - Scheppach HMS850 Traduction Des Instructions D'origine

2. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Str. 69
D - 89335 Ichenhausen
Dear Customer,
we hope your new tool brings you much enjoyment and suc-
cess.
Note:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.

3. Layout (Fig. 1-19)

1. On/Off switch
2. Slide block
3. Push stick
4. Hand crank
5. Chip extractor
6. Parallel stop
7. Clamping lever
8. Mounting for planing knife cover
9. Setting knob for the chip depth
10. Workpiece support
11. Rubber foot
12. Planing knife cover
13. Feed table
14. Planing table
15. Blade adjustment block
16. Allen wrench - small
17. Open-ended spanner
18. Scale infeed (Fig.3)
19. Pointer infeed (Fig.3)
20. Thicknessing table
21. Blade
22. Latch
23. Knife block
24. Anti-kick claws
25. Mounting with knife cover plate (Fig.5)
26. Allen wrench - medium
27. Chip extractor adapter Ø 100 mm
28. Allen wrench - large
29. Scale thickness plane (Fig.6)
30. Pointer thickness plane (Fig.6)
31. Locking screw
32. Knurled screw
32.1 Locknut
32.2 Washer
33. Locking screw
33.1 Washer
34. Fixing screw chip extractor
35. Overload switch
36. Washer
37. Allen screw
38. Angle scale parallel stop (Fig.5)
39. Angle pointer parallel stop (Fig.5)
40. Blade covering plate
40.1 Hexagon socket screw
40.2 Washer

4. Scope of delivery

• Plane (1x)
• Push stick (1x)
• Slide block (2x)
• Open-ended wrench (1x)
• Allen wrench, small (1x)
• Allen wrench, medium (1x)
• Allen wrench, large (1x)
• Rubber foot (4x)
• Washer (4x)
• Allen key (4x)
• Original operating instructions (1x)
GB 17