Table des Matières
Publicité
Felt and liner installation
4a - Install the protective felt for the floor.
4b - Cut the protective felt with a cutter or a pair of scissors.
4c - Place the liner in place at an outside temperature between 20 and 25°C.
4d - Match the corners of the liner with the bottom corners of the pool.
4e - Hang the liner in the lip of the rail.
4f - Position the locking ring all around the pool. Start in the middle of the wall.
4g - Stretch the liner to the maximum.
4h - Put in 2 cm of water.
4i - Remove existing folds and fill the pool with water up to 5 cm below the jetstream installation.
Cutting the liner and jetstream installation
5a - Install the gasket and jetstream frame using the stainless steel screws provided.
5b - Cut the liner inside the jetstream frame.
5c - Connect the air mixing hose to the front and rear parts of the jetstream box. Insert the hose into the air inlet socket. Secure with a hose clamp. Cut the air
hose to the correct length.
5d - Attach the pneumatic hose to the opening provided for this purpose in the jetstream system and connect it to the socket of the PN button (switching the
pump on and off). Tighten the hose by hand on the pneumatic switch and on the jetstream housing.
5e - Insert the entire front cover into the jetstream housing and screw in the unit with the 4 stainless steel screws provided.
Cutting of discharge nozzle, brush and skimmer socket
6a - Position the discharge nozzle and brush plug from inside the pool.
6b - Cut the liner at the discharge nozzle and brush socket, leaving a gap of about 2 mm. Insert the white seals (B), the nozzle and the brush plug.
6c - Tighten the outer nuts of the discharge nozzle and brush plug sufficiently to ensure tightness by means of the trick, if necessary mentioned on the diagram
6d - Cover the threaded part of the end caps with Teflon tape in a counter-clockwise direction.
6e - Screw the end caps onto the delivery and brush socket.
6f - Example of pipe positioning at the skimmer and brush socket
6g - Brush socket - discharge nozzle Glue the elbow, shut-off valve, corresponding connection and PVC pipes cut to length according to the ground
configuration.
6h - Glue the previously assembled assembly to the outlet of the brush socket and discharge nozzle. Close the shut-off valves.
6i - After covering the Teflon threaded part, screw the threaded stop valve into the skimmer body.
6j - Glue the rigid PVC pipe and elbow to the stop valve. Close the valve after the gluing has set and refill the basin to 5 cm below the beams.
6k - Install the gasket and skimmer frame.
6l - Screw the skimmer assembly together using the 18 flat head screws to be removed from the screw bag provided in the skimmer box.
6m - Cut the liner inside the skimmer frame. Finally, place the flange cover by clipping it into place.
6n - Correct water level at mid-height of the skimmer.
Mounting the spotlight
7a - Insert the screws into the 4 holes in the front of the assembly frame and slide the silicone gaskets over the screws on the back.
7b - After drilling the liner and beam with a Ø 25 mm drill bit, screw the assembly frame vertically at a distance of 50 mm to the right or left of the hole,
ensuring that the silicone seals are correctly positioned.
7c - Unscrew the fixing nut of the cable bushing and remove it from the cable.
7d - Insert the lamp cable into the liner hole and pull it out. Then carefully push the cable feed-through into the liner hole and push it as far as it will go, making
sure that the white seal is in contact with the liner.
7e - Then slide the fixing nut onto the lamp cable and screw it onto the cable feed-through. If you are using a universal wrench or pliers, make sure that you do
not overtighten or damage the nut.
7f - Wind the necessary length of cable to pull the spotlight out of the water.
7g - Unscrew the black nut and tighten the cable outside the pool. Position the pool spotlight so that the word «TOP» on the front ring is above and insert the
fixing screw into the top hole. Then tighten the lower screw at the bottom of the spotlight.
Be sure to follow the instructions for use given in the instructions accompanying the spotlight.
Installation of the pine coping stones.
• the coping stone is a finishing element. It is strictly forbidden to walk, run or sit on it. Are not covered by warranty: colour
changes, deformations (cracks, fissures, checks, knots or splinters) natural or resulting from improper installation.
8a - Pre-drill the inner coping stones approximately every 70 cm and screw them in. Start at least 3 cm from the ends.
8b - Pre-drill the outer edges.
8c - Screw in the outer coping stones.
8d - Position the corner and straight plates. Pre-drill and screw in using 6x30 screws.
9
Ladders
The use of ladders must be limited to access to the pool
The maximum weight allowed is 150 kg. The pool ladder must be placed in a safe position when not in use..
9a - Retrofit the ladder. To do this, flush the air below the steps if necessary.
9b - Mark the location of the ladder fasteners.
9c - Drill the coping stone and reinforcement with a Ø 50 mm hole saw. Identify the location of the bracket fixing screws and drill holes.
9d - Place the bracket in the hole and secure with two 6x60 screws.
9e - Position the wooden ladder against the horizontal reinforcement below the coping.
9f - Locate and drill the holes.
9g - Mark the locations of each bolt on each of the rungs and drill holes to lock the ladder.
10
Connecting and using the jetstream system
CAUTION!
• The electrical connection of the pump and the jetstream control unit must be carried out by a qualified electrician.
• The power supply must be disconnected with the differential circuit breaker (FI) before any work is carried out on the unit.
10a - Mount the PVC pipes and fittings as shown in the illustration. Note: Before gluing, first proceed with a dry assembly to check that all parts fit together.
• Clean the hose and connecting parts with the paint stripper.
• Do not use abrasive paper to clean the smooth PVC pipe.
• After cleaning, the surface must be matt. Do not touch the surface again as soon as it has been cleaned.
• Apply the adhesive along the longitudinal axis of the pipe and the connecting pieces.
• Assemble the two parts after applying the glue. Insert the parts fully into each other without turning them and hold them together for a few
moments.
• Then remove the excess glue with a brush.
• Do not use the glue at temperatures below 5°C. The assembly must be done quickly.
10b - Connect the pneumatic hose to the electro-pneumatic box. Be careful not to bend the hose.
10c - Connect and fix the air hose to the outer housing of the jetstream using the hose clamp and mount its check valve to the wall outside the pool.
Be sure to follow the instructions for use given in the instructions accompanying the jetstream kit.
49
Publicité
Table des Matières
