3M PPS Manuel D'utilisation page 4

Directions for Use:
• For Professional Use Only.
• Requires the use of a 3M™ PPS™ spray gun adapter (sold separately) to attach the 3M™ PPS™
Type H/O Pressure Cup to the spray gun. Reference Figure 1.
• Optional use of 3M™ PPS™ Mix Ratio Film Insert PN 16091 (Large), PN 16066 (Mini), sold
seperately.
• Requires the use of 3M™ PPS™ Lids and Liners PN 16024 (Large), PN 16114 (Mini), sold
seperately, to contain the material to be sprayed.
• Requires an operating pressure of ≤ 10 psi (69 kPa, 0.69 Bar) to the 3M™ PPS™ Type H/O
Pressure Cup. The 3M™ PPS™ Type H/O Pressure Cup contains a built in "pressure relief valve"
located in the base of the cup to avoid over pressurizing. If the pressure relief valve is damaged,
the 3M™ PPS™ Type H/O Pressure Cup must be replaced.
• Use Only Genuine 3M Parts and Accessories. Reference Figure 2 Component Listing.
Setup Sequence:
1. Insert optional 3M™ PPS™ Mix Ratio Film Insert (3) into the 3M™ PPS™ Type H/O Pressure Cup (1) if
desired. Otherwise, insert a 3M™ PPS™ liner (4) into the 3M™ PPS™ Type H/O Pressure Cup (1) and
add the desired amount of material to be sprayed.
2. Insert a 3M™ PPS™ lid (5) onto the 3M™ PPS™ liner (4) and press down until secured.
3. Align the opening on the Retaining Collar Shroud Assembly (6) with the 3M™ PPS™ lid lock tabs (5a)
and screw the Retaining Collar clockwise onto the 3M™ PPS™ Type H/O Pressure Cup (1) and hand-
tighten.
4. If the material will not be sprayed immediately, a 3M™ PPS™ plug (7) can be inserted into the lid spout
to seal contents.
5. When ready to spray the contents, remove 3M™ PPS™ plug (7) if used, and connect the spray gun with
the previously installed 3M™ PPS™ adapter to the 3M™ PPS™ Type H/O Pressure Cup. Reference
Figure 1.
a. While aligning the 3M™ PPS™ adapter with the tabs on the 3M™ PPS™ Lid and the Retaining Collar
Shroud Assembly, press down to fully seat and then turn gun slightly clockwise until the locking tabs
on the 3M™ PPS™ Retaining Collar Shroud Assembly (6a) and the 3M™ PPS™ Lid (5a) have fully
engaged the lugs on the 3M™ PPS™ spray gun adapter.
6. Attach the cup pressure hose (2) from the spray gun to the pressure port (1b) on the 3M™ PPS™ Type
H/O Pressure Cup. The hose clip on the cup (1a) may be used to hold the hose securely in place while
spraying.
7. Connect the spray gun to the air supply.
8. With the spray gun and the 3M™ PPS™ Type H/O Pressure Cup held perpendicular to the ground, pull
the trigger and adjust to the desired cup pressure, not to exceed a maximum operating pressure of 10
psi (69 kPa, 0.69 Bar). Caution: Pressure relief valve (1c) at the base of the cup will open at 30psi
(207 kPa, 2.07 Bar) and relieve excess pressure. Keep trigger pulled until air from inside the 3M™
PPS™ Lid and liner has been totally evacuated and a steady spray of material is coming from the spray-
head of the gun. This will allow the gun to be held and sprayed upside down without fl uid interruption.
9. Spray materials normally, periodically check the pressure to the cup to ensure pressure does not exceed
maximum operating pressure.
10. When done spraying, disconnect the input air supply from the spray gun.
11. Attention: Before disassembling the gun from the cup, the pressure must be relieved by
disconnecting the cup pressure hose at the base of the cup (1b).
12. While holding the spray gun upright, pull the trigger to allow any remaining material to drain out of the
fl uid passage in the spray gun and 3M™ PPS™ adapter back into the 3M™ PPS™ liner:
Attention: Failure to do so will result in a material spill on the 3M™ PPS™ Retaining Collar
Shroud Assembly.
13. Disconnect the 3M™ PPS™ Type H/O Pressure Cup from the spray gun at the 3M™ PPS™ adapter by
turning the gun counter-clockwise slightly to disengage locking tabs and pull gun upwards to separate
from the cup assembly.
English - 3