Scheppach 5806801903 Traduction De La Notice Originale page 24

21. Have your tool repaired by an expert
• This electric appliance is in accordance with the
relevant safety rules repairing of electric appli-
ances may be carried out only by experts other-
wise it may cause considerable danger for the
user.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
General safety regulations and accident preven-
tion
It is essential that you read the safety regulations and
operating instructions in their entirety and follow the
information contained therein in order to eliminate the
possibility of an accident or potentially dangerous sit-
uation from occurring while working with the machine.
• Always check the device, the mains cable and the
plug before using the device. Only operate the tool
when it is in good working order and is not damaged
in any way. Damaged parts have to be replaced im-
mediately by a qualified electrician.
• Always pull the power plug out of the socket out-
let before doing any work on the machine, before
changing tools and whenever the machine is not
being used.
• To prevent damage to the power cable, always lead
the power cable away from the rear of the machine.
• Keep the tools in a safe place and out of the reach
of children.
Special safety instructions
1. The pillar drill was designed in such a way so as
to all but eliminate potential hazards when the
machine is properly used. However, there are a
few safety precautions to observe in order to en-
sure that all residual hazards are ruled out.
2. Ensure proper voltage
The voltage must comply with the specifications
on the rating plate.
3. Use a socket-outlet with earthing contact
The device may only be operated from an outlet
with the properly installed earthing contact.
4. Extension cable
The cord cross section of an extension cable must
measure at least 1.5 mm
wind a cable reel prior to use. Check the cable
for defects.
5. Protection against electrical shock
Keep the device away from moisture. The device
must neither be damp nor be operated in a humid
environment. Prior to every use, check the device
and the mains cable with plug for damage. Avoid
bodily contact with earthed parts e.g. pipes, hot
elements, etc.
24 / 60
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
. Always completely un-
2
6. Protection against fire and explosion
There are spark producing components inside the
device. Do not use the device in the vicinity of
combustible liquids or gases. Otherwise there is a
risk of fire or explosion.
7. Handle the device with care
Do not use the cable to pull the plug out of the
socket. Protect the cable from heat, oil and sharp
edges. Keep your tools sharp and clean so that
you can work efficiently and safely. Follow the
maintenance regulations and the instructions for
changing tools.
8. Wear suitable work clothes and personal protec-
tion equipment
Loose clothing is not suitable, as it can be caught
by moving parts, causing you to become entangled.
Wear a hair net if you have long hair. As a general
rule, jewelry should not be worn when working with
machine tools. Ensure that you wear safety gog-
gles. Not doing so could result in eye injury.
9. Keep your work area neat and tidy
Disorder in the work area can easily lead to acci-
dents. Do not leave any tools, objects, or cable in the
direct vicinity of the work area, as this poses a trip-
ping hazard! Ensure that there is sufficient lighting.
10. Watch out for other persons
Watch out for other persons (especially children)
when using the device, and keep them away from
your work area. Do not let anyone touch the de-
vice or the power cable.
11. Store the tools in a safe location
Store unused devices in a dry, locked location
that is out of the reach of children.
12. Avoid overloading the device
Operate the device only within the specified out-
put range. Do not use any low-powered machines
for heavy duty work. Do not use tools to perform
work for which they were not intended.
13. Maintain a steady foothold
Ensure that you maintain a steady foothold while
working. Avoid abnormal body positions and al-
ways keep your balance.
14. Pull out the mains plug
Pull out the mains plug when not using the tool, pri-
or to maintenance, and when changing the drill bit.
15. Pull out the power plug.
Ensure that the mains connection is protected by
at least a 10 A-rated fuse.
16. Avoid unintentional start-up
Ensure that switch is turned off when plugging the
plug into the socket.
17. Keep an eye on your work
Always keep an eye on your machine and the ob-
ject you are working on. Never use the machine
when you are not concentrating or are distracted.
Never use the machine when you are under the
influence of alcohol or are taking medication.
18. Maximum workpiece size
Workpieces (max. 20 x 20 cm) may only be pro-
cessed if they can be clamped securely on the
drill table or in the vise.