Remote Control; Remote Control Of Matching Products; Ipod Compatibility - Cambridge Audio azur 740C Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22

Remote control

The 740C is supplied with an Azur Navigator remote control that
operates both this CD player and other Cambridge Audio Azur amplifiers.
Insert the supplied AAA batteries to use.
Note: The remote may be in Amp mode when first activated. Please refer
to the Amp Control section for more information.
Standby/On
Switches the unit between On and Standby mode.
Open/Close
Opens and closes the disc tray.
Numerical Track select
Press the number of the desired track. The track will then
be played from the start of the track.
Track select
To select a track number greater than ten, press -/--
followed by the track number.
Bright
Alters the brightness of the display backlight. There are
three levels of brightness: Bright, Normal, and Off.
Play /
Stop /
Pause
Press the relevant button to play, stop or pause the CD.
Skip
Right Skip - Press once to skip forward by one track on the
CD. Press and hold to skip forwards through tracks.
Left Skip - Press once to skip backward by one track on
the CD. Press and hold to skip backwards through tracks.
Search
Press and hold to search within the selected track. Right
button to fast forward, left button to rewind.
Menu
Menu
Press to access the 740C menu system on the front panel
display. Please refer to the 'CD player setup' section of
this manual for more information.
Select
Select
Press to accept the item/function highlighted in the
display menu. Please refer to the 'CD player setup' section
of this manual for more information.
Program, Remain, A-B, Repeat, Intro,
Random, Space
Read the 'Operating instructions' section of this manual
for information on the functions of these buttons.

Remote control of matching products

Amp Control mode
The 740A/C remote control comes with an Amplifier
Control button, that when pressed, puts the remote
into Amp mode, allowing operation of a Cambridge
Audio Azur amplifier. When pressed, the LED will light
up for 7 seconds (to let you know you are in Amp
mode), and will then flash when any of the relevant
circled Amp buttons is pressed. All other remote
buttons are inactive when in Amp mode.
The functions relevant to the amplifier are as follows:
Standby/On
Switches the amplifier between On and Standby mode.
Numerical buttons 1-6
Press to change the input source to the amplifier. Button
6 toggles Tape Monitor on/off.
Mode
Mode
Press to switch between Volume and Balance modes.
Mute
Mutes the audio on the amplifier. The mute mode is
indicated by MUTE appearing and the volume level being
Prog
replaced by two flashing dashes in the display. Press
again to cancel mute.
Amp
Mode
Control
Increase or decrease the volume of the amplifier output.
Vol
Speaker A/B
Speaker
A/B
Press to scroll through the speaker sets connected to the
loudspeaker terminals on the back panel (speaker sets A,
B or A and B).
Vol
Bright
Adjust the backlight of the front panel display; bright, dim
or off.
To exit Amp mode (and return to CD mode), press the Amp
Control button again (the LED will light up for one second).
Menu
Select
iPod
Repeat
A - B
Remain
The 740A/C remote can also control the basic functions of
Apple iPod's when mounted in Apple's Universal Dock (or
Intro
Random
Space
other docks compatible with the Apple Remote). Refer to
your dock's instruction manual on how to connect it to
your amplifier. To use the Azur remote to control the
Speaker
docked iPod, put the remote into Amp mode and press
A/B
one of the following buttons:
Play/Pause
Press to play the iPod, press again to pause play.
Press once to skip forwards or backwards one track.
Menu
Press to return to the iPod main menu.
azur
Volume
compatibility
TM
Skip
740C
7

Publicité

Table des Matières
loading

Table des Matières